- The tank clean-out access will be on top of the tank. You should be able to get a copy of the original permit from them. Check with the Tax Department to find out when the home was built and that should correspond with the year the septic system was installed.
How do I find my cleanout?
The location of your cleanout depends on the size of your home and your local climate. If you live in a colder area, your cleanout is most likely located inside your house near a bathroom, utility room or garage. Homes built on a slab foundation also sometimes have an outdoor cleanout.
Where is the cleanout on a concrete septic tank?
The septic tank should be cleaned from a cleanout port – usually located in the center of the tank.
How do you know when your septic tank needs to be cleaned out?
Common Signs You Need Septic Tank Pumping Services
- Slow or Frequently Clogged Drains. Since your septic tank is connected to the entire network of drains throughout your home, your sinks, showers, and even toilets can exhibit signs of a problem.
- Sewage Backup.
- Regular Gurgling Noises.
- Strong and Pungent Odors.
Where is the clean out pipe located?
The cleanout is usually a 4-inch-diameter pipe with a screw cap that has a square knob or indentation on the top. It’s most likely going to be popping up from the ground outside your home between the foundation and the street. The cleanout might also be on the side of the home, closest to the bathroom.
Where is my main drain cleanout?
Follow the drainage pipe in your home to find the cleanout. The line will often be right outside your home, but it could also be on the inside. The cleanout is usually right next to the foundation of your home, so look for a plugged pipe coming out of the floor.
Do all septic tanks have filters?
First, not all septic tanks have a filter, especially the older septic tanks. Now many government agencies require or recommend a filter when a septic tank is installed. Cleaning a septic tank filter is different than pumping out a septic tank and cleaning it.
What to do after septic is pumped?
After you have had your septic tank pumped by a trusted septic company, there are some things you can and should do as the septic system owner.
- 1) Get on a Schedule.
- 2) Take Care of the System.
- 3) Know the Parts of Your System.
- 4) Check Other Possible Issues.
How many lids are on a septic tank?
A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.
How long can a septic tank go without being pumped?
You can wait up to 10 years to drain your tank provided that you live alone and do not use the septic system often. You may feel like you can pump your septic tank waste less frequently to save money, but it’ll be difficult for you to know if the tank is working properly.
How do you clean sludge out of a septic tank?
How to Reduce Sludge in a Septic Tank Without Pumping
- Install an aeration system with diffused air in your septic tank.
- Break up any compacted sludge.
- Add a bio-activator or microbe blend.
- Maintain the aeration system.
- Add additional Microbes as required.
Can a septic tank never be pumped?
What Are the Consequences of Not Pumping Your Tank? If the tank is not pumped, the solids will build up in the tank and the holding capacity of the tank will be diminished. Eventually, the solids will reach the pipe that feeds into the drain field, causing a clog. Waste water backing up into the house.
Can I shower if my septic tank is full?
Unless the toilet’s overflowing or the bath spigot is filling the tub with blood, plumbers and exorcists aren’t usually on our minds. When the waste water from your toilet, shower, sinks and washing machine leave your house, it’s combined. When it hits the septic tank, however, it begins to separate.
Is my septic tank full or clogged?
If the septic tank is completely clogged, water will back up into the house quickly. If the septic tank is only partially clogged, the drains will become slow as the water struggles to wind its way down into the septic tank.
What are signs of septic tank problems?
7 Warning Signs Your Septic System Is Failing
- Gurgling Pipes. They would occur when you run water in the house (e.g. when using the sink or shower) or flush the toilet.
- Bad Odours. It’s never a pleasant experience when this occurs.
- Water At Ground Level.
- Green Grass.
- Slow Drainage.
- Blocked Pipes.
How To Install a Septic Tank Sewer Cleanout
- The days of dealing with your septic system (and its associated expenditures) are not over even once it is safely buried. Septic tank maintenance will be required, which essentially boils down to pumping the tank every couple of years as so. Thus, sludge at the bottom does not rise over the level where it would flow into your yard (yuck). In order to prevent this, the Environmental Protection Agency recommended that you get your septic system drained once every one to three years. Pumping the tank will cost you between $300 and $400, according to Cook’s estimates. Make sure your tank is inspected to determine if it needs to be pumped at the absolute least. If you don’t want a sewage plant in your backyard, trust us when we say this is not the type of thing you want to let go. It is possible to reduce maintenance costs in a number of ways. Simply reduce water use by installing low-flow toilets and without running the water for longer periods of time than is necessary to complete the task. Moreover, in addition to investigating the expenses of constructing and maintaining an on-site septic system, make sure to check and understand all of your local rules and regulations pertaining to wastewater treatment and other associated concerns. EPA.gov/septic has further information about this.
A clean-out port in your drain pipes may save you a lot of time and money, as well as avoiding a potentially nasty issue in some situations. In the event of a blockage, a clean-out allows you to quickly and easily access the drain line, and in some cases, it can avoid flooding inside your house. If the clean-out is correctly installed, it may also be utilized for routine septic tank cleaning while pumping out the septic tank.
Step 1
Clean-out ports in your drain pipes may save you a lot of time and money while also preventing a potentially nasty problem in the future. In the event of a blockage, a clean-out allows you to quickly and easily access the drain line, and in certain cases, it can avoid flooding within your house. If the clean-out is correctly installed, it may also be utilized for routine septic tank cleaning when the tank is being pumped out for maintenance.
Step 2
3 to 6 inches deeper than the drain line should be dug out of the ground. In order to have enough space to work, you will also need to expose 3 to 4 feet of the pipe on either side. Remove any loose dirt from the drain line and make ensure that no water or appliances are running inside the house in order to keep the drain line as dry as possible.
Step 3
Remove a portion of pipe from the drain line by cutting into it. The length of the excised part should be the same as the length of the tee fitting. Make sure to account for the flange on the tee fitting, which will be used to enter the drain line on both ends of the fitting. Make use of the pipe cleaner to clean both ends of the drain line as well as the fitting on the end of the line.
Step 4
A portion of pipe was removed by cutting into the drain line. When the excised part is measured against the tee fitting, it should match. Make sure to account for the flange on the tee fitting, which will be used to enter the drain line on both ends. Make use of the pipe cleaner to clean both ends of the drain line as well as the fitting on the end of the pipe.
Step 5
Place the PVC pipe cap on top of the new pipe and tighten it down. It is recommended that you acquire a threaded cap so that it may be removed easily when service is necessary. A pop-out fitting is another option to consider. If there is a backup of water in the pipe, the weighted cap on this fitting will keep it securely in place. This will cause the insert to pop out and enable the water to drain outdoors instead of backing up into the house. These are not permissible in all jurisdictions, so verify your local codes before putting them in.
Tip
When cutting into the drain line, always sure to use eye and hand protection. There will be sewage leftovers in the line, and you will want to prevent your eyes and skin from being contaminated as much as possible. Some homeowners may build a clean-out on both sides of the septic tank so that they can have easy access to all drain pipes as well as the tank itself while doing maintenance.
Septic Tank Clean-Out 101
Septic tanks of various shapes and sizes are pumped out by John Kline Septic Services. From residential to commercial to municipal work, there is something for everyone. Maintaining your septic tank is essential, whether you’re in need of a clean-out or you simply want to understand more about the procedure. To learn more, continue reading or contact us now to arrange service. We provide same-day service for emergencies, and our technicians are available 24 hours a day, seven days a week. Always In order to ensure that your septic tank gets cleaned out through the largest available opening, Your septic tank or system may have more than one entry point, depending on the type of tank or system you have installed.
- This is normally covered with a cement lid or manhole cover that is 18-24 inches in diameter and is often raised to grade with an extension.
- It also makes it difficult to completely clean out the tank, therefore it’s critical to ensure that your tank is well cleaned from the primary entry.
- In spite of the fact that we recommend that you have your tank pumped out every two to three years, depending on the size of your tank and the number of people living in your home, you may be able to extend the period between clean-outs without suffering any difficulties.
- When it comes to septic tank cleaning, we recommend that you never go more than FIVE years between cleanings to ensure everything is operating correctly and that your tank is filtering out waste in the appropriate manner.
- Ensure that your septic tank is easily accessible before scheduling your septic clean-out.
- Make a notation on your manhole cover or access port if it is hidden by your landscaping so that your technician can easily locate the cleanout when he or she arrives on site.
- Simply inquire or contact us in advance to inquire about the possibility of installing a riser at the time of your septic pumping.
Are you prepared to get your septic tank cleaned? We provide business and residential septic pumping services in Lancaster, Pennsylvania and the adjacent areas, including York, Lebanon, Berks, Chester, and Dauphin counties, as well as the surrounding areas. Make a call right now at 717-898-2333.
How to Clean a Septic Tank
Pumping septic tanks of all sizes is what we do here at John Kline Septic Services, Inc. There are occupations ranging from residential to commercial to municipal. Maintaining your septic tank is essential, whether you’re in need of a clean-out or you simply want to understand more about the procedure. To learn more, continue reading or contact us to book service now. Our experts are on call 24 hours a day, seven days a week to provide same-day assistance for emergencies. Always In order to ensure that your septic tank is cleaned out through the largest possible access, Your septic tank or system may have more than one entry point, depending on the type of tank or system that you have.
- This is normally covered with a cement lid or manhole cover that is 18-24 inches in diameter and is often raised to grade by an extension.
- Since a result, it is critical that you clear out your tank thoroughly from the main access point, as this will prevent appropriate tank cleaning from occurring.
- You may be able to extend the period between clean-outs before encountering difficulties, even though we recommend having your tank pumped out every 2-3 years.
- Avoid postponing your clean-out too long if you are the kind who enjoys the waiting game since doing so might result in septic backups or even system damage.
- Inspect the condition of your septic tank and make sure it is easily accessible.
- Never put a car or other heavy machinery on top of your septic system, and keep bushes and shrubs out of the way of the system.
- Our team can build an extension or a “riser” to pull your manhole cover up to ground level if it is below grade, which means it is buried and inaccessible to you.
- Please see this link for further information about septic tank risers.
- Our business and residential septic pumping services are available in Lancaster, Pennsylvania and the neighboring regions, which include the counties of York, Lebanon, Berks, Chester, and Dauphin.
- 1 Locate your tank. It is best to begin with the sewage pipe at the lowest level of your home if at all feasible. Follow the path it takes out of the house after it’s out of the house. It’s possible that your tank is buried in the ground. Identifying the tank now will save you time and money later on, regardless of whether you or an inspector clean the tank. 2 Remove the tank’s top by digging it out. It’s possible that your tank is buried underground. Take a shovel and clear away the dirt from around the top of the tank before the examination begins. Your tank will have an access port lid, which should be sturdy and well-secured when closed.
- Step 1: Locate your water tank. At the event that it is possible, begin with the sewer line in the lowest level of your home. Follow the path it takes out of the home once it has left the building. The location of your tank may be unknown. It saves time and money to locate the tank immediately, regardless of whether you or an inspector clean the tank afterwards. 2 The tank’s top may be removed by digging around it. It is possible that your tank is buried beneath the earth. Take a shovel and clear away the dirt from around the top of the tank before the inspection takes place. It is likely that your tank will have an access port lid, which should be sturdy and secure.
- Advertisement
- s3 Cracks should be checked on the tank. Damaged areas should be checked all the way around the tank, including the inside. Cracks must be fixed by a professional once the tank has been pumped in order to prevent the system from failing. Keep an eye out for any corroded or damaged sections on the inlet and outlet pipes that are necessary for drainage. If your tank is equipped with a distribution box or a pump chamber, make sure everything is in working order.
- In order to determine whether or not water from your home, such as from the toilet or washing machine, makes it into your tank and subsequently drains effectively, it is helpful to run some water from your home.
- 1Make a slit in a pipe. Begin with a ten foot (3 m) length of PVC pipe. Separate it into two sections: a six inch (15.24 cm) segment and a nine and a half foot (2.9 m) section, using a saw or PVC cutter
- 2 Glue the pipes together as a group. PVC cement should be poured into the elbow joint. Using the cement and joint, attach the smaller pipe to the top of the bigger pipe. A straight pipe will protrude straight to the right or left in a “L” configuration
- 3cap both ends of the pipe. PVC caps may be purchased at the same hardware shop where you purchased the pipes, cement, and cutters. 4 Attach the caps to the pipes so that they are tight and prevent water from flowing through them. Lower the stick into the hole. Assemble the scum stick by holding it in a “L” form with the smaller pipe at the bottom and facing out to one side. Reduce the pipe’s diameter until it can be held against the top layer of septic tank waste without breaking through
- 5 lowering the pipe Make a mark on the stick. Make a mark on the scum’s top point with a marker or a piece of masking tape. When the pipe is resting on top of the scum layer, make a mark at the point where the pipe spans from the ground to the very top of your tank
- 6Push through the scum layer until the mark is no longer visible. Push the stick all the way through the muck. Some people find it necessary to twirl the stick so that the pointed end bursts through. When you get to the bottom of the scum layer, you’ll see that the stick is traveling through water rather than through the resistive fat and oil layer. Continue to hold the stick against the bottom of the scum in the same manner as you held it against the top of the scum, keeping the smaller pipe flat and off to the side so that the stick takes on the shape of a “L”
- 7 Make a second mark on the stick. Once again, a marker or tape should be used to designate where the scum layer terminates. Make a note at the point where the pipe crosses the ground and enters the tank’s very top
- Eight Measure the distance between the markers. Carefully remove the stick and place it on a tarp to catch any drips. Make a note of the distance between the two marks you created and use a tape measure to measure it. This represents the depth of the scum level. When the fat and oil layer reaches barely three inches (7.62 cm) above the bottom of the exit pipe, the tank must be pumped to remove the remaining liquid. Advertisement
- 1Make a slit in a pipe. Partition a ten-foot (3-meter) length of PVC pipe into five-foot (1.5-meter) portions. In order to construct a secure two-part stick, glue the pipes together as shown in the diagram. Connect the two pipes together using a straight adaptor or a threaded coupler from the hardware shop, as shown. PVC cement should be used to secure the ends in the connection
- 3cap each end. PVC caps are also available at your local hardware shop. Put one on either end of your stick and twist them together. It should be tightened so that no sewage may enter the pipe
- 4 Wrap a piece of white cloth around one end of the stick. A white cloth, towel, sock, or Velcro can be used to make a mark on the sludge to indicate the level of the sludge. Wrap the material around one end of the pipe for up to three feet (.91 m) or the whole length of the pipe, whichever is shorter. 5Push the stick through the scum hole after securing the material with the Velcro backing, tape, or string. You can drill a hole in the top layer of the tank with a stick designed for testing its scum depth if you haven’t previously done so. Then drop the sludge stick through the opening until you feel it hit the bottom of the tank
- 6remain in position for three minutes while you do this again. Allow for a minimum of three minutes of resting time on the stick. The longer you keep the stick in your hand, the more likely it is that the sludge will stain your white material
- 7Remove the stick from your hand. Continue to bring the stick back up, keeping it steady as you pull it up through the hole you formed earlier in the process. You will not discolor the stick as long as you do not move it. Prepare the stain by spreading it out on the ground where it will not be ruined and where you will be able to wipe the stick afterwards
- 8Measure the stain. Make a note of the length of the stain starting from the bottom of the stick with a tape measure. In order to prevent the sludge or scum from occupying more than one third of the tank’s depth (approximately 12 inches or 30.48 cm high), the tank must be pumped. It is necessary to pump the tank if the sludge layer is within six inches (15.24 centimeters) of the bottom of the output pipes. Advertisement
- 1 Remove the cap from the tank. During your yearly checkup, lift the tank’s lid to have a better look inside. Remove the lid and look for the pipes that lead to the waste tank and the pipes that lead to the water supply. The baffles are contained within them, and they keep scum and sludge in place.
- 2Remove the filters from the machine. Put on a pair of rubber gloves for protection. Reach inside the outlet baffle using your hands, a rake, or a hoe to remove the obstruction. Take the filter out of the machine. Even though it may be brightly colored and have a handle on the end, if your tank has one, it will be located inside the outflow baffle. 3Rinse the filter thoroughly. Holding the filter over the intake side of the septic tank and spraying it with a hose or dipping it in a pail of water are both options. Check to see that all of the solids have fallen back into the tank or bucket. Fill the tank with any waste that has accumulated once you have done rinsing
- Inspect the filter for signs of wear and tear. Examine the filter for any cracks or particles that may be obstructing it. When the filter is not cleaned on a regular basis, it becomes clogged and ceases to function. It is recommended that you replace the filter if it is not cleanable or looks to be damaged. Looking around the edges of the filter is important whether you are putting the old filter back in or installing a new one. It’s possible that the filter has an arrow on it. Ensure that the filter is correctly installed so that the arrow points downwards into the drainage system. When the filter is securely seated in the baffle, replace the tank’s lid with a firm grip. Advertisement
- 1 Pump the tank once every several years or as needed. Many individuals make the mistake of assuming that the tank does not require treatment as long as the piping looks to be in working order. It is possible to save thousands of dollars in costly repairs by doing regular maintenance on your tank before sludge builds up and liquid drains cease to flow. Every one to three years, or whenever the sludge and scum levels have occupied approximately one-third of the tank’s volume or have approached the exit pipe, this should be performed.
- The smaller the tank or the greater the number of people served by the tank, the more frequently it will need to be cleaned. A 750-gallon tank, which is normal in a two-bedroom home, will sustain two people for around four years if they do not pump it. With just four inhabitants, it will survive less than two years without pumping
- Annual treatment will maintain the tank clean and allow any issues to be addressed before they become catastrophic septic failures at a cost of a couple hundred dollars
- And
- 2Clean up the garbage. Pumping is accomplished by the use of a cast-iron pump that can be turned on and off. The pump takes out the particles that are unable to be broken down by bacteria and transports them to a holding container, such as the inside of a tanker. If you remove the sludge and scum, there is no need to add bacteria or water into the system. Waste disposal for septic tanks. Even if you attempt to pump out the tank on your own, you must dispose of the trash in accordance with local regulations. The trash must be transferred by tanker to a place determined by the government that is distant from water and locations where people congregate. As a result, it is preferable to leave it in the hands of a specialist. Advertisement
Create a new question
- Question For what reason is it risky to clean up a septic tank? David Balkan is a licensed professional plumber who also serves as the CEO of Balkan Sewer and Water Main Service and the President of Balkan Sewer and Drain Cleaning, among other positions. With over 40 years of experience as an active owner of these businesses, David is well-versed in the challenges that arise with water service lines, sewers, and drain lines. David has served on the Executive Committee of the Sub Surface Plumbers Association of New York for more than 30 years and is now the Chairman of the Master Plumbers Council’s Committee on Plumbing. As a result of his expertise and solution-oriented approach, Balkan Sewer and Water Main Service has grown to become the biggest and most trusted sewer and water main service in New York City, and the recipient of the 2017 Angie’s List Super Service Award. Answer from a Professional PlumberExpert Sewer gas, which is prevalent in septic systems, has the potential to be lethal. It’s a quiet murderer that kills in a matter of minutes, therefore I strongly warn homeowners never to attempt to repair their own septic system. Employ the services of a professional to ensure your safety.
Question For what reason is it risky to clean up a septic system? David Balkan is a licensed professional plumber who also serves as the CEO of Balkan Sewer and Water Main Service and the President of Balkan Sewer and Drain Cleaning, among other roles. With over 40 years of experience as an active owner of these businesses, David is well-versed in the challenges that arise with water service lines, sewers, and drain lines. David has served on the Executive Committee of the Sub Surface Plumbers Association of New York for more than 30 years and is a Committee Chairman of the Master Plumbers Council.
Answer from a Professional Plumber It is possible to die as a result of the sewage gas that is found in septic tanks.
To ensure your safety, consult with a specialist.
- Every one to three years, have your tank examined and pumped out by a professional. A little amount of money spent on regular maintenance is preferable to dealing with a septic system that isn’t functioning properly. Higher water use, such as when numerous people reside in the house or when you use a hot tub, causes the tank to fill up more quickly. Non-waste items such as baby wipes and grease should not be disposed of. These clog the system and cause it to malfunction.
Advertisement
- Advertisement
Advertisement
Things You’ll Need
- A shovel, two ten-foot (3-meter) PVC pipes, a PVC cutter or saw, PVC cement, a PVC elbow joint, a PVC connector, and four PVC end caps A white cloth, a sock, or Velcro is recommended. Tarp, measuring tape, hose and bucket, baffle filter, etc.
About This Article
Summary of the ArticleX Maintaining the cleanliness of your septic tank will save you money on costly repairs down the road. Annual filter cleaning and tank pumping are required to keep your septic tank in good working order, but you may save money by doing it yourself. Generally speaking, your filter will be positioned in the tank’s exit baffle and will be brightly colored. Cleaning it is as simple as spraying it with water from the tank or submerging it in a pail of clean water for an hour or so.
The sludge and scum levels in your tank should be pumped out every one to three years, or whenever they reach a third of the total capacity.
Continue reading for additional information, including how to measure the sludge and scum depths in your septic tank.
Thank you to all writers for contributing to this page, which has been viewed 68,206 times so far.
Did this article help you?
Everything else that goes into a septic system, aside from waste water, should be contained within the tank itself. That is precisely what the tank is for. Sand and other heavy particles will sink to the bottom of the container, while sludge, grease, and other substances will float to the top. All of these “solids” should be removed at least once every five years, if not more frequently. It is recommended that the waste water only be discharged from the tank into a small distribution box and then to all of the perforated drainfield lines in the system.
A simple system in this location consists of a 1,000-gallon tank, a d-box, and 210 feet of drainfield line for up to three or four bedrooms.
The soil type and usage decide how much additional drainfield length is required.
If they were coming from a tank, the stench coming from a tank would be substantially greater than the stink coming from the other end of a drainfield line. The tank should be located in close proximity to the home. Mike
Sewer Clean Out for Residential Homes 101
a wooded trail / Photo courtesy of Fotolia Septic system failures can be prevented by utilizing a variety of fail-safes in contemporary plumbing. Your home is well-protected against sewage backups, with everything from drain traps to sump pumps and vent pipes. The sewage clean out is an extremely vital component of this system, and you should be aware of its existence. Despite its harmless look, having one or more clean outs in your home’s sewage line may have a significant impact on both the health of your sewer line and the health of your wallet.
What is a Sewer Clean Out?
In most cases, the sewer clean out is a capped pipe that is positioned on or near your property line and connects to the lateral sewage line. In plumbing, a lateral sewer line is a pipe that links the sewage lines in your house to either the municipal sewer system or your septic tank. Septic waste can back up into drains when the lateral becomes blocked, causing a nuisance as well as potential health risks for anyone who are exposed to it. Maintaining your sewer pipes and draining water in the event of a backup are two important benefits of having a clean out.
How to Find the Sewer Clean Out
On or near your property line, you will find the sewer clean out, which is a sealed pipe that connects to your lateral sewage line. Your home’s sewage lines are connected to the municipal sewer system or your septic tank by a lateral sewer connection. Septic waste can back up into drains when the lateral becomes blocked, causing a nuisance as well as potential health hazards for anyone who are exposed to it. An installed sewer clean out allows you to maintain your lines free and to drain water if you ever have a backup situation.
- The Sidewalk Should Be Checked– In many localities, the location where your lateral joins the municipal sewer line is indicated on the sidewalk. Along the curb and sidewalk, look for a letter ‘S’ that has been stamped or painted. If you come across this marker, you may easily visualize a straight line from the mark to your house, where the lateral may be located if you look closely. In certain situations, you may even be fortunate enough to come upon a clean out in the neighborhood of where you are looking. Search Near Your Foundation– In many circumstances, locating the sewer clean out near the road is impractical, or the home’s former owners elected to have more than one sewer clean out built. In these cases, you should search near your foundation. When you have a septic system in place, sewer clean outs are also typically positioned close to the home’s location. If you are more than three feet from the foundation, you will most likely find the cap anywhere between the road or septic tank and the point at which your home’s sewage line exits the foundation and enters the ground
- Look for extra clean outs inside– Some homes, particularly older ones, may have clean outs that are either hidden within the structure or protrude from the exterior walls of the structure. Check the basements, crawl spaces, and attic for probable vent pipe sites along with the vent pipe. Most of the time, indoor sewer clean outs will look to be a junction with one side of the Y or T shaped intersection being capped. These are important for keeping your interior pipelines in good condition, even if they are not essential.
What if the Property Lacks a Sewer Clean Out?
It is possible that older properties may not have a sewer clean out. The latter is particularly true if one is not obligated to do so by municipal or state plumbing regulations. It is typically preferable to have one installed in such situations. Sometimes your home has a clean out that has just been covered up by dirt, which is another situation. If you suspect the house has a clean out but have been unable to identify it, you may want to conduct some light digging along the ground where you assume the clean out should be in order to locate it.
Benefits of a Sewer Clean Out
While having a sewage clean out is mandated by law in certain jurisdictions, if you have an older property or live in a state where they are optional, you may find yourself without one. There are, however, various advantages to having a clean out installed on your home, including the following:
Lower Maintenance Costs
The clean out gives you direct access to the sewage lateral on your property’s property. This means that a plumbing professional may monitor the water flow from each individual faucet in your home to verify that there are no blockages or other pipe concerns during their monthly maintenance visits.
Cheaper and Easier Cleaning
When it comes to cleaning your sewage lines, a plumber would normally have to remove your toilet or perhaps climb onto the roof to do so.
They will have easier access to the sewage lateral if they have a sewer clean out performed. Because of the time and effort savings, you will have a lower overall bill.
Protects Your Landscaping
If you have a big clog, one advantage that only becomes evident in an emergency situation is the fact that a sewer clean out can assist eliminate the need to dig up your yard in the case of a clog. The sewer lateral, in contrast to many of the pipes within your home, is totally underground and cannot be inspected for wear or damage without digging the area where it is located. The sewer clean out serves as an entry point for your lateral, allowing it to be more readily examined and maintained.
BackflowPrevention
It can also be used as an external drain if a large amount of blockage is encountered. Taking the clean out cap off will allow you to drain the extra water, which will save your property from flooding. When there is an issue with the municipal sewer that is forcing water back up into your lateral, this may also be beneficial.
How to Install a Sewer Clean Out
It is necessary to complete many steps in order to install a clean out. Depending on the circumstances, your local municipality may provide programs to assist with the cost of installation, particularly in situations where a sewer clean out was not previously required by code. Before you begin, make sure you check for any available programs or grants, as well as any necessary permissions or licenses. It is also recommended to get expert assistance if you do not have prior experience splicing or installing sections of pipe in order to prevent making costly blunders.
Choosing a Clean Out Type
The first and most important step before starting any work is to choose the sort of sewer clean out you will be using. There are three alternatives accessible at the present time: Double Clean Out– The double clean out is the most common type of clean out used in contemporary installations. It contains two shafts that link to the lateral pipe in a ‘U’ configuration, making it the most common type of clean out used in modern installations. The cap that is closest to your home allows for simple access to the city end of the lateral, but the cap that is closest to the street allows you to preserve the house end of the lateral (see illustration).
Despite its T design, the test tee clean out provides access to both ends of the lateral, but it can be difficult to use for clearing obstructions owing to a 90 degree angle at the intersection.
Excavation and Installation
A segment of pipe will need to be excavated in order to find your lateral line. This can be accomplished using either conventional hand tools or leased equipment, with caution to avoid damaging the lateral pipe. As soon as you have completely exposed the required area of the pipe, you should measure out the length of pipe that will be removed. The type of cutting equipment you’ll need will depend on the material that your lateral pipe is constructed of. Once the undesirable portion has been removed, you will be able to measure, cut, and install the new junction section in its place.
Most of the time, it’s advisable to put a container box around the top to keep it from being overgrown or buried too quickly.
Professional Cleaning Cost with a Sewer Clean Out
Even while cleaning your own lateral line may appear to be a cost-effective choice, there is always the possibility of causing damage to the pipes. A professional plumber can complete the task more efficiently and at a lower cost if they have access to the sewage system through a sewer clean out. As a result, they use less tools and less effort than if they were required to dig up your yard or snake the lateral from an interior location of your property. With a basic estimate range of $99 to $900 and an overall average of $288, HomeAdvisorgives provides a reliable service.
When it comes to costs, CostHelper gives more specific estimates, with an estimated cost of snaking your lateral ranging from $148 to $900, with an average cost of $410.
Additional costs will include a video examination of the line, which will cost between $100 and $800.
Some plumbing businesses may quote you a fixed charge but then urge you to tack on extra services in order to raise the total cost of the job.
COMMON PROBLEMS — JT’s SEPTIC
Despite the fact that cleaning your own lateral line may appear to be a cost-effective option, there is always the possibility of causing damage to your pipes. If you have access to a sewer clean out, it is more efficient and less expensive to hire a professional plumber to complete the job. The reason for this is that they have more direct access, requiring less tools and less effort than if they had to dig up your yard or snake the lateral from a location within the house. With a basic estimate range of $99 to $900, and an overall average of $288, HomeAdvisorgives provides a reliable service.
In greater detail, CostHelper estimates that the cost of snaking your lateral will range between $148 and $900, with an average cost of $410 per foot.
Additional costs will include a video examination of the line, which will cost between $100 and $8,000.
Some plumbing businesses may quote you a fixed charge but then urge you to tack on extra services in order to raise the total cost of the work. Take your time and search around to get the ideal combination of quality and price.
GURGLES
Whenever you flush the toilet, the water gurgles, the toilet takes an unusually long time to flush, or the water in the shower turns brownish after you have done the laundry, you are receiving a subtle indication that trouble is brewing. In order to determine when the tank was last pumped, look through your records and then contact your preferred septic provider for assistance.
ODORS
If you are experiencing unpleasant odors within your home, such as rotten eggs, it is likely that a trap or vent inside your home is not venting correctly. Call your plumber right away since these gases are harmful to both people and animals!
ODORS OUTSIDE IN THE YARD
At times, the smells emanating from the roof vents will seep into the yard due to meteorological conditions. Make use of a plumber to elevate the roof vents and/or to place a charcoal filter in the vents, as needed. It’s important to remember that your septic tank is vented via the roof.
SURFACING IN THE YARD
The smells from the roof vents can sometimes be carried down into the yard by the wind. Engage the services of a plumber to elevate the roof vents and/or install a charcoal filter in the roof vents. Keep in mind that your septic tank’s exhaust is vented through the ceiling.
HEAVY SOLIDS- OVERDUE FOR PUMPING
At times, the smells from the roof vents will be carried down into the yard by the wind. Engage the services of a plumber to elevate the roof vents and/or place a charcoal filter in the vent. Keep in mind that your septic tank is ventilated through the roof vents!
grease build up in sewer pipes
Fats and grease should never be flushed down the toilet or sink. They have the potential to harden the lines and cause failure; they have the potential to generate an excessive buildup of the floating scum layer in the septic tank; and they have the potential to go into the disposal regions and adjacent soils and completely block the system off. A shattered lid can pose a serious threat to both animals and children. It is conceivable that they will fall through the cracked or broken lids and will not be noticed until it is too late to save themselves.
crushed or settled pipe
This is the second most prevalent problem we notice in septic systems that are less than 10 years old. In addition to blocking flow, loose fill soil surrounding the tank is causing a backup into the house since it is pulling the pipe with it as it settles. We have even observed instances when contractors installing new systems do not correctly pack the fill earth below the pipe, resulting in pipe settlement on systems that have not been utilized or have only been used for a short length of time (see below for an example).
SEWER OUTLET PROGRESSION
When it comes to modern septic systems, this is the most typical issue we encounter. Take note of the fact that the unsupported outlet pipe is being driven down by settling dirt.
Watch as the water level in the tank rises, forcing the flow of water in the inflow sewage line to slow. This will eventually result in a clog in the inflow sewer line at some point. The solids flowing down from the house will not be able to enter the tank correctly because of the high water level.
examples of settled sewer pipes:
INSTALLATION OF A TANK AND/OR REPAIR OF SEWER PIPESTHE “POLY” PIPEIMAGES BELOW PROVIDE AN EXAMPLE OF WHAT PIPENOTTO USES WHEN INSTALLING A TANK AND/OR REPAIR OF SEWER PIPES However, despite the fact that this grade of sewer pipe is less expensive at the time of purchase, it might end up costing you a lot of money in the long run!
settled inlet sewer pipe on unused system:
Even if the septic system has not been utilized in some time, it is conceivable that problems will be discovered during the inspection process. Pipes might settle on unoccupied ground and in yards as a result of faulty installation and/or automobiles and/or ATVs running over the pipes without realizing they are there. It may be beneficial to all parties to have a skilled inspector take a look at the system and diagnose any concerns, even though the County does not require an examination on an underused system before transferring ownership.
Roots growing in and around the septic tank:
In addition to disrupting the system by clogging or destroying drainage and distribution lines, tree roots can also enter the tank, causing it to leak. Foul odors, poor drainage, and patches of vegetation in the leach field are just a few of the signs that you may have a root problem.
ERODED BAFFLES
Solids are kept in the septic tank and away from the disposal area with the use of concrete baffles. Using baffles to reduce agitation of wastewater entering the septic tank and prevent particles from escaping the tank and entering the drainfield, baffles can assist avoid drainfield damage and extend the life of the drainfield. If the baffles are broken, missing, or have never been placed, the drainfield’s life expectancy will be reduced significantly. Baffle repair normally entails the placement of a plastic tee at the end of the sewer pipes to prevent them from clogging.
orangeburg sewer pipes
Orangeburg pipe was made in Orangeburg, New York, from 1860 to 1970, and was utilized to plumb numerous septic and wastewater systems throughout Yavapai County during that time period. Orangeburg pipe is produced from rolled tar paper (wood pulp that has been sealed with hot pitch) and was considered a low-cost alternative to metal, particularly after World War II, because of its flexibility and durability. In fact, the pipe itself is so soft that professionals might cut it with a knife during the installation process!
Orangeburg, on the other hand, is known for degrading over time (it has a 50-year lifespan at the most) and deforming when subjected to pressure.
If the septic system is approved, Orangeburg will normally be stated on the permits as the material for the inlet and/or outflow pipe material, respectively.
How Much Does It Cost To Clean Out a Septic Tank? See Breakdown
When it comes time to have your septic tank cleaned out, there is one very crucial thing to consider.
“How much does it cost to pump a septic tank?”
The solution is not as straightforward as you may expect, but it is also not going to need the completion of a four-year degree to figure out. In order to wipe away years of buildup from your laundry, toilet, shower, sink, and jacuzzi, there are a few things that influence the amount you may have to spend for the “Mega Flush.”
Let’s get started.
First and foremost, you should be aware that septic tanks are analogous to individuals. They are available in a variety of forms and sizes, and their ages range from recent to ancient. Their health problems are also quite diverse, as are their demeanors and dispositions. Some are fearful and prefer to remain concealed from view, buried beneath the surface of the earth. People are more forceful, use prominent risers, flashing lights, and even audible alarm systems to alert others to their commanding presence in the room.
- The septic tank is still on the table, believe it or not.
- Let alone those who behave more like the adolescent who ate too many burritos for lunch and then insisted on releasing his farts in the center of your kitchen while you were attempting to cook supper!
- The clinical research “Various Personality Disorders Common to Septic Tanks” has been sponsored by Shankster Bros.
- But it is a discussion for another day.
The costs pertaining to the cleaning of a septic tank can be divided, (or multiplied), into 4-5 categories:
You should be aware that septic tanks are similar to individuals in some ways. He or she can be found in a variety of sizes, shapes, and ages, ranging from newborn to elderly, with a wide range of health concerns, and with a wide range of manners and dispositions. The timid want to remain concealed from public view, buried beneath the surface of the earth. People are more forceful, use prominent risers, flashing lights, and even audible alarm systems to alert others to their commanding presence in the building.
Yes, we’re still talking about a septic tank right now!
Let alone those who behave more like the adolescent who ate too many burritos for lunch and who insisted on releasing his farts in the center of your kitchen while you were attempting to cook supper!
What on earth is that foul odor? The clinical research “Various Personality Disorders Common to Septic Tanks” has been sponsored by Shankster Bros. and is expected to be published in a journal in the near future. We’ll save that for another time.
Let’s break these costs down:
As previously said, septic tanks are available in a variety of designs and sizes. Some people are surprised to learn that the septic tank sizing requirements for homes are based on the number of bedrooms, that the requirements for churches are based on the seating capacity of the auditorium, that the requirements for factories are based on the number of employees, and that the requirements for campgrounds are based on the number of campsites.
Current septic tank sizing requirement guidelines in Indiana are as follows:
Home has 5 bedrooms and a 1500 gallon tank. 4 bedroom house with a tank of 1250 gallons. a three-bedroom house with a 1000 gallon tank 750 gallon tank for a two-bedroom house 500 gallon tank for a one-bedroom house It’s worth noting that any jetted bathtub, such as a hot tub or jacuzzi, with a capacity greater than 125 gallons qualifies as an additional bedroom. Always keep in mind that many of the systems being installed today are equipped with a secondary tank that serves as a pump station, pumping your sewage out to the leach field or sand mound, where it is distributed through piping and receives its final treatment before being leached away into the earth.
2.) Accessibility of tank
Unfortunately, some septic tanks have been constructed in difficult-to-access locations. Consider the possibilities: beneath the deck, beneath the garage floor, beneath the new living room that was constructed a few years ago, beneath that enormous pine tree that I planted 40 years ago, and so on. Yes, we have witnessed each and every one of those scenarios, as well as countless more. The presence or absence of a Riser in your tank is another factor that affects accessibility. This is a pipe that is attached to the lid of your septic tank and extends to the surface of the earth below the tank.
This may necessitate digging in order to expose the tank’s access lid, which may incur additional costs.
Some service providers will charge you an additional fee if they have to use more than one length of pipe to reach your storage tank.
does not share this sentiment!
3.) Distance from the service area
According on the location of the client in relation to the service provider’s service area, many service providers charge on a sliding scale. Take, for example, Shankster Bros., which has its headquarters in Northern Indiana. A client in Kentucky will be charged more than a customer in Kosciusko, Whitley, Wabash, Fulton, Elkhart, or the adjacent counties if we get a call from that client.
4.) Frequency of cleaning
Some of our clients, particularly those who live near lakes, are employing tanks that solely hold septage rather than allowing it to be leached out into the environment.
This necessitates the need to pump them out on a regular basis, perhaps as frequently as once each week. Because of the regularity with which the service is provided under these particular circumstances, we are able to provide lower costs.
5.) Volume the amount of gallons
Customers with enormous amounts of garbage to dispose of, such as campers, big business establishments, and even wastewater treatment plants, may be required to do so at certain times. In this situation, it will be necessary to mention special price once more. So, when you phone the office to inquire about price, be prepared to provide the following information so that the receptionist can provide you with an accurate quote as promptly as possible:
- The location of the property in need of cleaning services
- The size of the septic tank, if it is known
- And Whether your tank is equipped with an access riser or not.
Alternately, if you are already a customer, we already have all of that information on file with your name or address, and we can quickly look up your information on file with either Shankster Bros, Strombeck Brothers, North Webster Septic Tank Service, or Shepler septic tank cleaning, and provide you with an instant quote based on the information you have already provided us.
A general average cost to clean out a septic tank in Northern Indiana is as follows, although you can see specific pricing varies according to the parameters I have outlined above:
Cleaning a 1000 gallon tank will cost between $200 and $300.00. Over 1000 gallons, per gallon, there is a 7 cent per gallon charge. Fee for digging – $75.00 per hour Line cleaning costs between $225 and $300.00. Riser for retrofitting – $190.00 Whenever you want aseptic tank cleaning, pumping, or inspection, please do not hesitate to contact Shankster Bros. at any time of day or night.
Everything You Need to Know About Septic Tank Cleaning
Septic tanks are tanks that are capable of being linked to a home’s plumbing system, as described above. They are frequently employed in rural locations where municipal sewage lines have not been established or are not already in use. Maintaining a clean, functioning septic tank is essential. This may be accomplished by having it pumped on a regular basis. Here’s all you need to know about maintaining the cleanliness of your tank.
Why Do You Need to Clean a Septic Tank?
Whenever you flush a toilet in your house, take a shower, or operate the washing machine, the used water and trash are transferred to your septic tank for proper disposal. In order for liquid to be transported out of the tank and into a drain field, the septic tank must be built in this manner. Waste, on the other hand, sinks to the bottom of the tank and remains there. After a period of time, the waste decomposes into a slimy or sludge-like substance. Pumping the tank eliminates this sludge material, keeping your tank from becoming so backed up that it becomes unable to operate or from overflowing into your backyard.
Can You Clean a Septic Tank Yourself?
Technically, it is possible to clean a septic tank on your own. Professionals, on the other hand, strongly advise against doing so. Cleaning a septic tank is a difficult and time-consuming operation. It takes a lot of effort. Incorrect use of the tank can result in harm to the tank as well as poor waste disposal or failure to remove all of the trash from the tank. There are a variety of reasons why you should employ a professional to clean your septic tank. A expert will be able to find and uncover your tank in a short period of time.
A professional is equipped with the gear necessary to effectively pump your storage tank. Besides that, a professional has the expertise and skills to remove all of the trash from your tank and dispose of it in an appropriate manner.
How Frequently Does Your Tank Need to Be Cleaned?
It is necessary to get your septic tank pumped on a regular basis in order to maintain it clean. You may be asking how frequently your tank should be pumped as a result of this. There are a variety of factors that influence how frequently your tank has to be pumped, including the tank’s size and location in your home, the number of people who live there, the quantity of waste generated by your household items, and whether or not you utilize enzymes or bacteria in your tank. In light of these considerations, a septic tank specialist may make an estimate of how frequently your tank should be flushed.
How Do You Know When Your Tank Is Due for Cleaning?
Your tank may also give you indications that it is time to get it cleaned in addition to presenting you with an anticipated pumping schedule from a septic specialist. When your tank needs to be pumped, you may notice that water is slowly draining from your house. When taking a shower, you may observe water puddling around your feet or sink water slowly draining away when doing the dishes. The presence of foul odors in your septic tank is another indication that it needs to be flushed. It is possible that scents will be present when your tank is completely full.
- Finally, if your tank is overdue for a pumping, it may begin to overflow as a result of the delay.
- Make sure you are aware of the location of your tank so that you can keep an eye out for any standing water in the region.
- All of your septic tank needs may be met by Al’s Septic Tank Service, which serves the greater Pauline, SC region.
- To book an appointment, please contact us right away.
How to Clean Out Field Lines for a Septic Tank
DEBOVE SOPHIE is credited with this image. /iStock/GettyImages
In This Article
- Is It Possible to Save It?
- The Pressure Washer Approach Incorporating Biological Additives into Septic Tanks
- Installing an Aerator
If your septic system has begun to malfunction despite regular tank pumping and proper routine maintenance, it’s probable that your drain field has begun to malfunction. Sometimes a drain field problem may be repaired, while other times it cannot be repaired. Despite the fact that you can try to clear up your field lines in the hopes that a clog is the source of the problem, you may find yourself in the midst of a more significant situation. Professional evaluation of your system and recommendation of the best course of action is always a good idea.
- The first is that it is only intended to be used for a limited period of time.
- Following that, it’s normal for the drain field to require extensive repairs or maybe replacement entirely.
- As the waste accumulates, it hardens into a thick sludge that is nearly impenetrable by water, so impairing the capacity of the drain field to drain correctly.
- If you are experiencing any of these issues, cleaning up your drain pipes will not provide a solution.
If you suspect that your system is blocked or has just reached the end of its useful life, you may definitely attempt to clear out your pipes. At times, it is effective; at other times, it is not. You may prefer to hope for the best, but you should be prepared for the worst case scenario.
The Pressure Washer Approach
When it comes to cleaning up drain field pipes, a frequent method is to utilize a high-pressure water jet. Sewer jet devices, such as the Clog Hog, attach to a gas or electric power washer and then feed into the pipe, clearing away any obstructions or buildup. This particular cleaning process may be approached from two different perspectives. The recommended technique is to locate and expose the downhill end of the drain field pipes, after which you may feed the water jet backward via the drain field pipes.
If you choose to take this path, some sludge will come out of the pipe and into the distribution box, and you will need to remove it.
Biological Additives in Septic Tanks
When cleaning out drain field pipes, it is usual practice to employ a high-pressure water jet. Sewer jet devices, such as theClog Hog, attach to a gas or electric power washer and then feed into the pipe, clearing away any clogs or buildup. In terms of this specific cleaning process, there are two ways. If possible, locate and expose the downhill end of your drain field pipes before feeding the water jet backwards down the drain field pipes. If you’re not sure where your pipe ends are or just don’t want to dig holes, you may enter your septic system’s distribution box and clean each drain line from there instead of digging holes.
How Does a Septic Tank Work?
Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.
How does a septic tank work?
Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.
It’s critical to understand how a septic tank works in order to maintain one.
Let’s take a look below ground and observe what happens in a properly operating septic system, shall we?
Understand that a septic system is a cafeteria for bacteria
Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.
- A layer of sludge settles to the bottom of the container.
- 4.
- Scum is mostly constituted of fats, greases, and oils, among other substances.
- Grease and oils float to the surface of the water.
- (5) A filter stops the majority of particles from reaching the exit pipe.
- The effluent is discharged into the drain field.
- Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.
When gravel is used to surround pipes, water can run into the soil and oxygen can reach germs. The garbage is completely decomposed by aerobic bacteria found in gravel and dirt. 9. Potable water seeps into the groundwater and aquifer system from the surface.
Septic Tank Clean Out: Don’t abuse the system
Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank. However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.
- Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to eliminate the sludge and scum that has built up within the tank. It is possible, however, to do harm to or even destroy a septic tank if you are not familiar with how the system functions.
Get your tank pumped…
Your tank must be emptied on a regular basis by a professional. Pumping eliminates the accumulation of sludge and scum that has accumulated in the tank, which has caused the bacterial action to be slowed. If you have a large tank, it may be necessary to pump it once a year; but, depending on the size of your tank and the quantity of waste you send through the system, you may go two or three years between pumpings. Inquire with your inspector about an approximate guideline for how frequently your tank should be pumped.
…but don’t hire a pumper until you need it
Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.
Install an effluent filter in your septic system
Garbage from your home accumulates into three distinct strata. The septic filter is responsible for preventing blockage of the drain field pipes.
Septic tank filter close-up
The septic tank filter is responsible for capturing suspended particles that may otherwise block the drain field pipes. Obtain an effluent filter for your tank from your contractor and place it on the outflow pipe of your tank. (It will most likely cost between $50 and $100, plus labor.) This device, which helps to prevent sediments from entering the drain field, will need to be cleaned out on a regular basis by a contractor to maintain its effectiveness.
Solution for a clogged septic system
If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.
- Keep the effluent filter in place since it is required by your state’s health law.
- Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
- Your filter, on the other hand, should not require cleaning every six months.
- A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
- A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
- Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.
For additional information on what should and should not be flushed down the toilet, contact your local health authority. More information on removing lint from your laundry may be found here.
Get an inspection
Following a comprehensive first check performed by an expert, regular inspections will cost less than $100 each inspection for the next year. Your professional will be able to inform you how often you should get your system inspected as well as how a septic tank functions. As straightforward as a septic system appears, determining its overall condition necessitates the services of a professional. There are a plethora of contractors who would gladly pump the sludge out of your tank, but many, in my experience, are unable to explain how a septic system works or how it should be maintained.
A certification scheme for septic contractors has been established in certain states; check with your state’s Secretary of State’s office to see whether yours is one of them.
Also, a qualified inspector will be able to tell you whether or not your tank is large enough to accommodate your household’s needs, as well as the maximum amount of water that can be passed through it in a single day.
As you learn more about how a septic tank works, your professional should be able to tell you whether or not your system will benefit from this treatment.
Alternatives to a new drain field
If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.
- Pipes should be cleaned. A rotating pressure washer, used by a contractor, may be used to clean out the drain septic field pipes. The cost of “jetting” the pipes is generally around $200. Chemicals should be used to clean the system. A commercial solution (not a home-made one) that enhances the quantity of oxygen in the drain field should be discussed with your contractor before installing your new system. Septic-Scrub is a product that I suggest. A normal treatment will cost between $500 and $1,000. Make the soil more pliable. The practice of “terra-lifting,” which involves pumping high-pressure air into several spots surrounding the drain field, is authorized in some regions. Some contractors use it to shatter compacted dirt around the pipes. Depending on the circumstances, this might cost less than $1,000 or as much as $4,000 or more.
Protect your drain septic field from lint
When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.
Don’t overload the septic system
Reduce the amount of water you use. The volume of water that flows into your tank, particularly over a short period of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to save water.
Meet the Expert
Septic systems, according to Jim vonMeier, are the solution to America’s water deficit because they supply cleaned water to depleted aquifers, according to vonMeier. He travels the country lobbying for septic systems, giving lectures, and giving testimony. For septic system inquiries, as well as information on the operation of the septic tank, contact him by email.