- The yard-based septic vent usually looks like a capped piece of white PVC above the leach field. It may also look like a candy cane shaped pipe in your yard. The purpose of this pipe is it works in concert with the roof vent pipe to allow the air pressure in the drain to equalize.
Where does pipe enter septic tank?
Inlet & Outlet Pipes: Wastewater from your home enters the septic tank through the inlet pipe. After the solids settle out, effluent leaves the septic tank through the outlet pipe and flows to the drain field. The outlet pipe should be approximately 3 inches below the inlet pipe.
How do you unclog a septic tank leading pipe?
Sprinkle the drain with baking soda, then dump vinegar into the pipe. Leave the mixture to sit in the pipe for an hour or two. Finally, flush the drain with hot water. If the clog is small, this could be enough to clear the pipe.
What is the pipe sticking out of my septic tank?
The white PVC pipes that stick up in the area of your drain field offer a “window” into how well it is operating (draining). They shouldn’t be removed but they can be cut down, level with the ground. Your septic system may have a “candy cane” vent pipe over the pump tank.
How deep should septic pipe be buried?
On average, trenches should be around 12-24 inches-deep, and wide enough to house your pipe comfortably before filling it in with soil and sod.
What kind of pipe goes from house to septic?
The septic tank should be positioned at least 50 feet from the house proper. ABS or PVC plastic or cast iron pipe can be used to connect the tank to the house drainage system. [We do not recommend using clay pipe nor “orangeburg” pipe.]
How do I know if my septic line is clogged?
Signs of Septic System Clogging: Water and sewage from toilets, drains and sinks backing up into your home. Bathtubs, showers, and sinks draining slowly. Gurgling sounds present in the plumbing system. Bad odors coming from the septic tank or drain field.
How do you know if your main line is clogged?
Signs Your Sewer Line May Be Clogged
- Dark Water. One of the signature symptoms of a main-drain clog is water backing up in your tubs or showers.
- Slow-Moving Drains. Take a minute to think about the drains in your home.
- Gurgling Sounds.
- Clogged Plumbing Fixtures.
- Turn Off the Water.
- Call a Plumber.
What are signs of septic tank problems?
7 Warning Signs Your Septic System Is Failing
- Gurgling Pipes. They would occur when you run water in the house (e.g. when using the sink or shower) or flush the toilet.
- Bad Odours. It’s never a pleasant experience when this occurs.
- Water At Ground Level.
- Green Grass.
- Slow Drainage.
- Blocked Pipes.
What are the blue pipes sticking out of the ground?
While natural gas and electricity power most furnaces today, many pre-1970s homes had fuel-oil powered furnaces and with that came an underground fuel oil tank. Evidence of this reveals itself in that pair of galvanized steel pipes sticking out of the ground within a couple feet of each other.
What is the PVC pipe sticking out of my house?
Some homes contain drain access pipes, which can be of PVC, and are intended for use if a clog forms in your main drain. They tie into the drain that leads out to the street sewer towards the end of the home sewer line. Check your basement or crawl space to see where the pipe ties in and cap it if necessary.
How do you hide septic vent pipes?
Several options exist for covering the vent pipes, such as functional birdbaths, fake rocks and Roman columns. Some manufacturers make birdbaths with a pedestal to fit over the vent pipe. Some come with odor-controlling filters, and can be set to a specific height.
Will a flooded septic tank fix itself?
Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.
What causes septic tank clogs?
In a clean tank, the solids are broken down before they drain into the field. If the tank isn’t pumped regularly, the solids may not break down and will instead enter the drainfield lines and cause a clog. Putting items into the tank that shouldn’t be there, such as hygiene products, can also cause problems.
How Your Septic System Works
Underground wastewater treatment facilities, known as septic systems, are often employed in rural regions where there are no centralized sewage lines. They clean wastewater from residential plumbing, such as that produced by bathrooms, kitchen drains, and laundry, by combining natural processes with well-established technology. A conventional septic system is comprised of two components: a septic tank and a drainfield, often known as a soil absorption field. It is the septic tank’s job to decompose organic matter and to remove floatable stuff (such as oils and grease) and solids from wastewater.
Alternate treatment systems rely on pumps or gravity to assist septic tank effluent in trickling through a variety of media such as sand, organic matter (e.g., peat and sawdust), constructed wetlands, or other media to remove or neutralize pollutants such as pathogens that cause disease, nitrogen, phosphorus, and other contaminants.
Specifically, this is how a typical conventional septic system works:
- All of the water that leaves your home drains down a single main drainage pipe and into a septic tank. An underground, water-tight container, often composed of concrete, fiberglass, or polyethylene, serves as a septic system’s holding tank. Its function is to retain wastewater for a long enough period of time to allow particles to sink to the bottom and form sludge, while oil and grease float to the surface and produce scum. Sludge and scum are prevented from exiting the tank and moving into the drainfield region by compartments and a T-shaped outlet. After that, the liquid wastewater (effluent) exits the tank and flows into the drainfield. The drainfield is a shallow, covered hole dug in unsaturated soil that serves as a drainage system. Porous surfaces are used to release pretreated wastewater because they allow the wastewater to pass through the soil and into the groundwater. In the process of percolating through the soil, wastewater is accepted, treated, and dispersed by the soil, finally discharging into groundwater. Finally, if the drainfield becomes overburdened with too much liquid, it can flood, causing sewage to flow to the ground surface or resulting in toilet backups and sink backups. Finally, wastewater percolates into the soil, where it is naturally removed of harmful coliform bacteria, viruses, and nutrients. Coliform bacteria are a kind of bacteria that may be found in the intestines of humans and other warm-blooded animals, with humans being the most common host. As a result of human fecal contamination, it is a sign of this.
The Guadalupe-Blanco River Authority has built an animated, interactive model of how a residential septic system works, which you can view here.
Do you have a septic system?
It’s possible that you’re already aware that you have a septic system. If you are not sure, here are some tell-tale symptoms that you most likely are:
- You make use of well water. In your home, the water pipe that brings water into the house does not have a meter. In the case of a water bill or a property tax bill, you will see “$0.00 Sewer Amount Charged.” It is possible that your neighbors have a septic system
How to find your septic system
You can locate your septic system once you have confirmed that you have one by following these steps:
- Taking a look at the “as constructed” drawing of your house
- Making a visual inspection of your yard for lids and manhole covers
- Getting in touch with a septic system service provider for assistance in locating it
Failure symptoms: Mind the signs!
A bad odor is not necessarily the first indicator of a septic system that is failing to work properly. Any of the following signs should prompt you to seek expert assistance:
- Water backing up into the drains of homes and businesses
- It is especially noticeable in dry weather that the drainfield grass is bright green and spongy. The presence of standing water or muddy soil near your septic system or in your basement
- A strong stench emanating from the area surrounding the septic tank and drainfield
How Does a Septic Tank Work?
Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.
How does a septic tank work?
Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.
It’s critical to understand how a septic tank works in order to maintain one.
Let’s take a look below ground and observe what happens in a properly operating septic system, shall we? After that, I’ll explain why things go wrong and offer you some tips on how to keep your system in peak operating condition.
Understand that a septic system is a cafeteria for bacteria
Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.
- A layer of sludge settles to the bottom of the container.
- 4.
- Scum is mostly constituted of fats, greases, and oils, among other substances.
- Grease and oils float to the surface of the water.
- (5) A filter stops the majority of particles from reaching the exit pipe.
- The effluent is discharged into the drain field.
- Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.
- The garbage is completely decomposed by aerobic bacteria found in gravel and dirt.
- Potable water seeps into the groundwater and aquifer system from the surface.
Septic Tank Clean Out: Don’t abuse the system
Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank. However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.
- Drains are used to dispose of waste that decomposes slowly (or not at all). Cigarette butts, diapers, and coffee grounds are all known to cause issues. Garbage disposers, if utilized excessively, can introduce an excessive amount of solid waste into the system. Lint from synthetic fibers is emitted from washing machine lint traps. This substance is not degraded by bacteria in the tank and drain septic field. Bacteria are killed by chemicals found in the home, such as disinfecting cleansers and antibacterial soaps. The majority of systems are capable of withstanding limited usage of these goods, but the less you use them, the better. When a large amount of wastewater is produced in a short period of time, the tank is flushed away too quickly. When there is too much sludge, bacteria’s capacity to break down waste is reduced. Sludge can also overflow into the drain field if there is too much of it. Sludge or scum obstructs the flow of water via a pipe. It is possible for tree and shrub roots to obstruct and cause harm to a drain field. Compacted soil and gravel prevent wastewater from seeping into the ground and deprive germs of oxygen. Most of the time, this is caused by vehicles driving or parking on the drain field.
Get your tank pumped…
Your tank must be emptied on a regular basis by a professional. Pumping eliminates the accumulation of sludge and scum that has accumulated in the tank, which has caused the bacterial action to be slowed. If you have a large tank, it may be necessary to pump it once a year; but, depending on the size of your tank and the quantity of waste you send through the system, you may go two or three years between pumpings. Inquire with your inspector about an approximate guideline for how frequently your tank should be pumped.
…but don’t hire a pumper until you need it
Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.
Install an effluent filter in your septic system
Garbage from your home accumulates into three distinct strata.
The septic filter is responsible for preventing blockage of the drain field pipes.
Septic tank filter close-up
Garbage from your home is deposited in three layers: Septic filters are designed to prevent blockages in the drain field pipes.
Solution for a clogged septic system
If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.
- Keep the effluent filter in place since it is required by your state’s health law.
- Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
- Your filter, on the other hand, should not require cleaning every six months.
- A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
- A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
- Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.
- More information on removing lint from your laundry may be found here.
Get an inspection
Following a comprehensive first check performed by an expert, regular inspections will cost less than $100 each inspection for the next year. Your professional will be able to inform you how often you should get your system inspected as well as how a septic tank functions. As straightforward as a septic system appears, determining its overall condition necessitates the services of a professional. There are a plethora of contractors who would gladly pump the sludge out of your tank, but many, in my experience, are unable to explain how a septic system works or how it should be maintained.
A certification scheme for septic contractors has been established in certain states; check with your state’s Secretary of State’s office to see whether yours is one of them.
Also, a qualified inspector will be able to tell you whether or not your tank is large enough to accommodate your household’s needs, as well as the maximum amount of water that can be passed through it in a single day.
You may be able to boost the performance of your system by using a product such as RID-X to introduce bacteria into the system. As you learn more about how a septic tank works, your professional should be able to tell you whether or not your system will benefit from this treatment.
Alternatives to a new drain field
If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.
- Pipes should be cleaned. A rotating pressure washer, used by a contractor, may be used to clean out the drain septic field pipes. The cost of “jetting” the pipes is generally around $200. Chemicals should be used to clean the system. A commercial solution (not a home-made one) that enhances the quantity of oxygen in the drain field should be discussed with your contractor before installing your new system. Septic-Scrub is a product that I suggest. A normal treatment will cost between $500 and $1,000. Make the soil more pliable. The practice of “terra-lifting,” which involves pumping high-pressure air into several spots surrounding the drain field, is authorized in some regions. Some contractors use it to shatter compacted dirt around the pipes. Depending on the circumstances, this might cost less than $1,000 or as much as $4,000 or more.
Protect your drain septic field from lint
When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.
Don’t overload the septic system
This device prevents lint from entering the system, particularly synthetic fibers, which bacteria are unable to digest and hence cause infection. Septic Protector is the name I gave to one of these filters that I designed myself. An additional filter is included in the price of roughly $150 plus delivery. See this article for further information on how to filter out lint from your clothes.
Meet the Expert
Septic systems, according to Jim vonMeier, are the solution to America’s water deficit because they supply cleaned water to depleted aquifers, according to vonMeier. He travels the country lobbying for septic systems, giving lectures, and giving testimony. For septic system inquiries, as well as information on the operation of the septic tank, contact him by email.
Everything You Need to Know About Your Septic Tank
What is a septic tank, and how does it work? A septic tank is a water-tight container that is often constructed of concrete, fiberglass, or polyethylene to prevent flooding (plastic). In fact, it is only one component of the entire septic system, which includes several other components such as a distribution box, pumps, float switches, aerators, filters, and other accessories. Septic systems are used to treat wastewater on-site in many rural and suburban areas that do not have access to centralized sewage systems.
The components of a conventional septic tank are depicted in the diagram below.
These are:
- The Tank: This is the water-tight tank into which wastewater from your house is sent once it has been collected. A hole, fracture, or any other structural damage should not be present. Access Ports: When a trained pumper comes to clean up your tank, they will utilize an access port. When it comes to tank cleaning, it is critical that the access port be large enough to allow the pumper to move the hose about within the tank properly. A common application for risers is to elevate septic tank access above ground level, eliminating the need to dig up your septic tank every time it has to be pumped. Last but not least, the access port should be securely secured with a child-resistant lid. It is vital for the protection of your family that septic tank lids are securely fastened with screws and that they are not cracked or damaged. Pipes for entering and exiting the septic tank: Wastewater from your house enters the septic tank through the intake pipe. After the particles have settled out, the effluent is discharged from the septic tank through the exit pipe and into the drainage field. There should be roughly 3 inches between the output pipe and the intake pipe. A baffle is fitted on the intake pipe within the tank, and it serves to keep the water out. It provides a variety of functions. Additionally, it helps to avoid the build-up of scum and its backup into the intake pipe It is also important for solids to settle in the tank that the input baffle be properly installed. When wastewater enters the septic tank, it should hit the entrance baffle, which will reduce the flow and prevent the tank from becoming agitated. This permits the contents of the septic tank to remain at rest, allowing the solids to sink to the bottom of the tank. The intake baffle can also prevent odorous odors from entering the sewage line and spreading throughout the home or business
- And It is even more crucial than the inlet baffle to have an exit baffle in place because it helps to prevent scum and other particles from flowing directly into the outflow pipe and eventually into the drain field. Gas Deflector/Effluent Filter: As gas bubbles climb to the top of a septic tank, they may bring sediments with them. This is why an effluent filter is used. A gas deflector prevents these solid-carrying gases from entering the output line by preventing them from entering. However, while not every septic tank is equipped with an effluent filter, it is strongly suggested as an additional safety to prevent particulates from entering your drain field.
Any of the above-mentioned components in your septic tank should be checked for damage or missing parts as soon as possible, and the problem should be resolved by a septic system specialist. What is the operation of a septic tank? Each and every drop of wastewater from your home is channeled via a main drainage pipe and into your septic tank. Solids are prevented from entering your drain field by using the septic tank, which is just a settling tank that serves as a filter. Ideally, the water should be kept in the tank for at least one day in order to enable time for the solids to settle.
- Heavy materials, such as dirt and digested waste, will sink to the bottom of the tank and form a sludge layer at the bottom of the tank.
- Effluent is the term used to describe the liquid that exists between the sludge and scum layers.
- It is critical that solids are given adequate time and space to settle before being used.
- In fact, the Pennsylvania Department of Environmental Protection mandates a minimum capacity of 900 gallons for any new septic tank installations in the state (the table below shows recommended septic tank capacities for different sized homes).
- Ideally, you should have your septic tank emptied every two to three years, according to the Pennsylvania Septage Management Association (PSMA).
- If a drain field has been ruined by a buildup of sediments, it might cost tens of thousands of dollars to rebuild it.
- It is crucial to understand that your septic tank must be completely filled with liquid in order to function effectively.
- The septic tank diagram shown above depicts the correct operating level of a septic tank in a residential setting.
- The result is that whenever more wastewater is added to the tank, an equal volume of effluent will be discharged from the tank and drain into the drain field.
- The opposite is true if the liquid level is higher than the outflow line, which may signal a blockage in a line downstream from the septic tank or in the drain field.
If you’re wondering if your septic tank is full, a skilled pumper will consider it “full” once solids have filled one-third of the tank’s capacity. This is the time of year when your septic tank will need to be pumped.
8 Signs of Septic System Failure
Septic tanks are an important resource for both homeowners and the surrounding community. Its goal is to store domestic wastewater in an underground chamber where it may be treated at a basic level. They are generally composed of plastic, fiberglass, and concrete and serve as a sewage disposal system for the home or business owner. Sewage can leak underground and move upward in the earth if a septic unit fails, which can cause flooding. Not only may this result in serious plumbing issues, but it can also pose a health threat over time.
If that’s the case, these are the eight indicators of a failing septic system.
1. Septic System Backup
Everything that has to do with plumbing in your home is tied to your septic system. Sewage and wastewater will no longer be able to enter the tank if your septic system malfunctions or becomes overburdened. Instead, it will remain in the pipes until it begins to rise to the surface again. Sewage and wastewater back up into sinks, drains, and even into your toilet as a result of this condition. A clogged septic tank is the most obvious indicator of a failing system. You should contact a qualified plumber as soon as you discover this symptom to get it repaired.
2. Slow Drains
Slow drainage might also be caused by a clogged septic tank. For example, if a septic tank is completely filled, it will no longer actively collect wastewater from the ground. This implies that your pipes will become blocked with sewage and will be unable to drain your plumbing appliances properly. Your drains will become naturally sluggish in draining water or other liquids, as a result of this phenomenon. Even if you utilize the best gear available to unclog your drain, you will not be successful since the fundamental problem is located in the septic tank.
3. Gurgling Sounds
When using plumbing appliances, you should also be on the lookout for any unusual sounds that may occur. For example, if you flush your toilet and hear strange gurgling sounds, you should call a plumber right once to assess the situation. Toilets generally emit water-related sounds that subside once the flushing cycle is completed. If, on the other hand, you hear sounds that sound like an upset stomach, you may have a serious problem. If you are hearing gurgling noises coming from your drains, the same logic applies.
4. Pool of Water or Dampness Near Drainfield
It is no longer possible to absorb wastewater in a septic tank when it is damaged or fails. This indicates that wastewater will naturally seep out of the earth as a result of the groundwater table. It has the potential to create a significant pool of wastewater near the drain field, as well as cause dampness in the same area. These are the most obvious indications of a failing septic system, and they should not be ignored. A pool of water near the drainfield will often appear as if it has been raining on your lawn for an extended period of time.
Dampness near your drainfield, especially if it hasn’t rained in several days, should be taken seriously. If you have reason to believe that your septic tank is full or broken, make a point of actively looking for these signs.
5. Nasty Odors
One such tell-tale indicator of a failing septic system is the development of foul odors near the drainfield and plumbing equipment. If you notice strong and nasty scents when you walk outdoors and tread onto your grass, it is possible that your septic tank has failed. If the bad aromas emanating from your house are the same as those emanating from the office, you can reach a similar conclusion. It is likely that sewage has entered your home through the drainfield and into your main drain line, resulting in these foul odors.
6. Unusual, Bright Green Grass Above Drainfield
Have you ever seen people applying mulch, fertilizers, and manure to their lawns in order to encourage it to grow more quickly? It is possible that sewage has the same features as manure, namely that it contains nutrients such as nitrogen, potassium, phosphorus, and micronutrients that plants can use to thrive. When you see exceptionally green grass near your drainfield, it is likely that wastewater is leaking into your lawn from the drainfield itself. Due to the fact that grass is naturally green, identifying this symptom might be difficult.
Pay close attention to your drainfield in order to identify this problem before it becomes too serious.
7. Blooms of Algae in Nearby Water
If you live near a body of water, such as a lake or pond, keep an eye out for unexpected algal blooms that appear out of nowhere. Due to the fact that most individuals regard the appearance of algae to be a regular occurrence, diagnosing this symptom can also be difficult. Algal blooms, on the other hand, occur when a huge concentration of algae forms in a body of water. They appear to be artificial and to be the result of excessive algal contamination in the water. When wastewater is present, it might lead to the growth of algae that is aberrant.
8. High Levels of Coliform in Water Well
A neighboring water well may also be able to identify abnormal amounts of coliform bacteria as well as high quantities of nitrogen dioxide (nitrogen dioxide). However, if your septic system fails, the water in your well will get contaminated with bacteria and harsh chemicals by effluent from the surrounding area. Give Us a Call Right Now! Any problems with your septic tank now occupy your thoughts? If this is the case, please contact us at (941) 721-4645 to talk with a member of our staff. You may also learn more about our septic services by visiting this page.
Frequently Asked Questions (FAQs)
Do you have any other queries concerning septic systems? Please let us know. If this is the case, you may find a comprehensive list of FAQs farther down on this page.
How much do septic system repair services cost?
- A septic system repair service might cost anywhere from $500 to $2,000 in labor and materials. The ultimate cost is determined by the extent of the task, the number of hours worked, and other factors.
Can a septic drainfield be repaired?
- Even though there is no quick remedy for drainfield repair, it is achievable if you employ an expert plumber or septic system specialist.
How often do septic systems need to be replaced?
- Septic systems may endure for more than 40 years if they are properly maintained. Every three years, the average septic tank should be examined and pumped out in order to avoid long-term problems and septic system failure.
How to Run a Septic Tank Line From Your House
A septic system is made up of two lengths of pipe that are connected together. Initially, it runs from the house, where the system services are located, to a tank, where the waste is separated and solids settle out. The second section runs from the tank to the drainage field, where fluids from the tank are dispersed into the earth underneath the tank.
The process of installing the first run of pipe is quite similar to that of installing a traditional sewage line. It is necessary to maintain a downhill slope to the storage tank.
Locating the Septic Tank
The tank serves as the nerve center of the septic system. It is required to be situated between the residence and the drainage field. Each and every septic installation must begin with a soil test, and depending on the results, soil conditions may necessitate the placement of the tank in a less-than-ideal site for digging sewer lines. Also required are minimum setback distances from property borders, functioning wells, surface water and other obstructions to provide a safe working environment.
Tank Depth
A standard septic tank has a 4-inch intake at the top, which is positioned towards the bottom. Ideally, a 1/4-inch-per-foot slope toward the pipe from the house should be maintained by the pipe connecting to it. To put it another way, for every 10 feet of distance between a tank and a home, the inlet must be 2 1/2 inches lower than where the pipe departs the house at its lowest point. The pipe usually exits at ground level, although it may need to pass beneath a foundation footing or concrete pad in rare cases.
Digging the Trench
The trench for the septic pipe should be dug before the hole for the tank since you will need a backhoe to complete the work and the tank will get in your way if it is already in the ground. To allow rainfall to drain properly, the pipe should be placed on a 2- or 3-inch bed of drain rock, so remember to account for this extra depth when digging. It is normal to use a four-inch pipe, and it should be installed far enough down to link with the main soil stack, which is a three-inch pipe that runs vertically past the main bathroom and through the roof of the home.
Precautions
Local building and health agencies will demand permits for a septic tank installation. You will also be required to submit a design plan before the permits will be provided, so prepare ahead of time. This layout should be developed in collaboration with a local builder who is familiar with the unique characteristics of the topography in your neighborhood. Stay away from planting trees or plants near the tank, drainage field, or any of the pipe systems. They will be drawn to the pipes in their hunt for nutrition, and their roots will be able to successfully block them.
Removal may be both expensive and time-consuming.
3 THINGS TO KNOW ABOUT SEPTIC TANK BAFFLES
By Admin on November 12, 2020 Your efforts to live as environmentally conscious as possible, as a responsible homeowner, are likely already underway, with practices such as recycling, composting, and purchasing energy-efficient equipment among your list of accomplishments. As a septic tank owner, you want to be sure that anything you put into your tank and septic field is causing the least amount of ground contamination as is reasonably practicable. Fortunately, there are a number of modest improvements you can do immediately to make your septic system even more ecologically friendly than it already is.
- Have your septic tank inspected and pumped on a regular basis.
- A bigger septic tank with only a couple of people living in your house, for example, will not require pumping as frequently as a smaller septic tank or as a septic tank that must manage the waste products of multiple family members will require.
- When in doubt about how often to pump your septic tank, consult with a professional for advice.
- In addition to locating and repairing any damage, a professional can ensure that the septic field is in good working order and that your septic tank is functional, large enough to handle your family’s waste, and not causing any unwanted pollution in nearby ground water.
- Avoid flushing non-biodegradable items down the toilet or down the toilet.
- Items that are not biodegradable are unable to properly decompose in the septic tank and might cause the system to get clogged.
- In addition to causing issues in your house, septic system backups can damage ground water in the area surrounding your septic field.
Towels made of paper Products for feminine hygiene Grease or fats are used in cooking.
grinds from a cup of coffee Even if you have a trash disposal, the food scraps that you flush down the drain and bring into your septic system may cause unanticipated harm to your plumbing system.
Food scraps can enhance the amounts of nitrogen and phosphorus in the wastewater, which can disturb the natural bacterial balance of the septic tank, among other things.
Water conservation should be practiced.
Exceedingly large amounts of water use will interfere with the normal flow of wastewater from your home into your septic tank.
Limiting the amount of time you spend in the shower and turning off the faucet while brushing your teeth, as well as purchasing a smaller dishwasher and washing machine that use less water, are all simple strategies to reduce water use in your home.
The following are some basic steps you can take to make your septic system more ecologically friendly: save water, maintain your septic system and tank, and recycle wastewater. To get answers to any of your septic tank-related issues, get in touch with the experts at Upstate Septic Tank, LLC.
How a Septic System Works – and Common Problems
This Article Discusses Septic Tanks are a type of septic tank that is used to dispose of waste. Field Sizing and System MaintenanceProblems with the Leach FieldSystem Performance Questions and comments are welcome. See Also: Septic System Frequently Asked Questions Articles on SEPTIC SYSTEM may be found here. In locations where there are no municipal sewage systems, each residence is responsible for treating its own sewage on its own property, which is known as a “on-site sewage disposal system,” or septic system, more popularly.
One of the most commonly seen types of leach field is composed of a series of perforated distribution pipes, each of which is placed in a gravel-filled absorption trench.
SEPTIC TANK
The wastewater is collected in the septic tank after it has been discharged from the house. Septic tanks are typically between 1,000 and 2,000 gallons in capacity and are made of concrete, heavy plastic, or metal, depending on the model. Highly durable concrete tanks, which should last for 40 years or more if they are not damaged, are the most common. Many contemporary tanks contain two chambers to boost the efficiency. Household wastewater is collected in the septic tank, where it is separated and begins to degrade before being discharged into the leach field.
- In the tank, oil and grease float to the top of the tank asscumand solid waste sinks to the bottom assludge.
- Bacteria and other microorganisms feed on the solids at the bottom of the tank, causing them to decompose in an anaerobic (without oxygen) process that begins at the bottom of the tank.
- Solids and grease must be pumped out of the system on a regular basis in order for it to continue to function properly.
- Each fresh gallon entering the tank sends one gallon out to the leach field, leach pit, or equivalent treatment location.
Leach Field
When used properly, a leach field (also known as a “drain field”) is a series of perforated pipes that are typically buried in gravel trenches 18 to 36 inches below grade — deep enough to avoid freezing, but close enough to the surface that air can reach the bacteria that further purify the effluent (see illustration below). As little as 6 inches might separate you from the ground surface, depending on your soil type and municipal regulations. It is customary to cover the perforated pipes with approximately two inches of gravel and a layer of topsoil that is 18 to 24 inches in depth.
- Grass is often sown above the ground.
- The leach field is comprised of rows of perforated pipes in gravel trenches that are used to spread wastewater over a vast area in order to further purify it.
- A bacteria-rich slime mat forms where the gravel meets the soil, and it is responsible for the majority of the water purification work.
- Despite the fact that wastewater freezes at a far lower temperature than pure water, freezing is still a hazard in cold areas.
- The leftover pathogens are converted into essential plant nutrients by these organisms, while sand, gravel, and soil filter out any solids that remain.
- If the system is operating effectively, the filtered wastewater will return to the aquifer as naturally clean water that is suitable for human consumption at this stage.
- Alternative systems may be permitted in situations when traditional leach fields are unable to function properly owing to poor soil conditions or a high water table.
These systems sometimes cost twice or three times as much as a regular system and require significantly more upkeep. Special systems may also be necessary in regions where there are flood plains, bodies of water, or other ecologically sensitive areas to protect against flooding.
SIZING THE LEACH FIELD
Using perforated pipes put in gravel-filled trenches, the drain field is sized to accommodate the number of beds in the house. In order for the system to function successfully, the leach field must be appropriately sized for the soil type and amount of wastewater, which is normally determined by the number of bedrooms in the house. In order for the liquid to seep into the soil, it must be permeable enough to do so. As a result, the denser the soil, the larger the leach field that is necessary.
- Better to have surplus capacity in your system than to have it cut too close to the bone.
- Septic tank backup into your house, pooling on the surface of the earth, or polluting local groundwater are all possibilities if the ground is incapable of absorbing the liquid.
- Dense clay soils will not absorb the liquid at a sufficient rate, resulting in a backup.
- If the soil is mostly composed of coarse sand and gravel, it might drain at such a rapid rate that untreated sewage can poison the aquifer or damage surrounding bodies of water.
- Alternative systems may be permitted in situations when traditional leach fields are unable to function properly owing to poor soil conditions or a high water table.
- Near flood plains, bodies of water, and other ecologically sensitive places, special systems may also be necessary to protect people and property.
SEPTIC SYSTEM CAREMAINTENANCE REQUIRED
If you take good care of your system, you will be rewarded with years of trouble-free operation. Pumping the septic tank on a regular basis is necessary to remove the particles (sludge) and grease layer (scum) that have built up in the tank. The solids will ultimately overflow and spill into the leach field, decreasing its efficacy and diminishing its lifespan if this is not done. The rehabilitation of a clogged leach field is difficult, if not impossible; thus, constant pumping is essential!
Cooking fats, grease, and particles may also wash into the leach field if the tank is too small for the amount of water being used or if the tank is overcrowded on a regular basis.
Extra water from excessive residential consumption or yard drainage can overwhelm the system, transporting oil and particles into the leach field and causing it to overflow.
In addition, don’t try to complete a week’s worth of laundry for a family of five in a single day. This will assist you in keeping the load controlled and will also help to extend the life of your system. To minimize overburdening the system, the following measures should be taken:
- Distribute your washing loads and other high-water-use activities across the week
- And In the kitchen and bathroom, use low-flow appliances, faucets, and fixtures. Toilets, in general, are the source of the greatest amount of water use. Water should be diverted away from the leach field from the yard, gutters, and basement sump pumps.
In addition, refrain from flushing sediments, strong chemicals, and just about anything else down the toilet or sink other than biological waste and white toilet paper. Avoid using garbage disposals in the kitchen. If you really must have one, keep it for small non-meat bits only. Avoid flushing chemicals or paints down the toilet since many chemicals can destroy beneficial microorganisms or cause water contamination in the surrounding area. Avoid flushing the following down the toilet:
- Grease, fats, and animal scraps
- Paints, thinners, chemicals, and pharmaceuticals
- And a variety of other materials sanitary napkins, tampons, and other supplies Paper towels and disposable diapers are examples of such products. Egg shells, coffee grounds, and nut shells are all good options. Antibacterial soaps and antibiotics are available.
It is preferable to put grass over the leach field and to refrain from driving or parking in the vicinity. Excessive weight placed on top of the drain field might compress the earth, diminishing its efficiency as a drain field. Drain pipes can also become clogged by trees and plants with invasive roots. In order to prevent damage to the leach field, the following measures should be taken:
- Heavy machinery should not be driven, parked, or stored on top of the leach field (or septic tank). Placement of a deck, patio, pool, or any other sort of construction over the leach field is prohibited. Remove any large trees or other plants with deep roots from the leach field. Grass is the most effective groundcover.
Even with careful use and routine maintenance, however, leach fields are not guaranteed to survive indefinitely. It is inevitable that the soil will get saturated with dissolved elements from the wastewater, and that the soil will be unable to absorb any more incoming water. The presence of an odorous wet area over the leach field, as well as plumbing backups in the house, are frequently the first indicators that something is wrong. Many municipalities mandate septic system designs to incorporate a second “reserve drain field” in the case that the first field fails.
A well constructed and maintained system should last for at least 20 to 30 years, if not longer than that.
More information on Septic System Maintenance may be found here.
SEPTIC SYSTEM PERFORMANCE PROBLEMS
Poor original design, abuse, or physical damage, such as driving heavy trucks over the leach field, are the root causes of the majority of septic system issues. The following are examples of common situations that might cause a septic system to operate poorly: Plumbing in the home. obstructed or insufficient plumbing vents, a blockage between the home and the septic tank, or an insufficient pitch in the sewer line leading from the house are all possible causes. Sewage tank to leach field connection Septic tank and leach field blockage caused by a closed or damaged tank outlet, a plugged line leading to the leach field caused by tree roots, or a blockage caused by sediments that overflowed from the tank Piping in the leach field.
- Most of the time, tree roots do not make their way through the gravel bed and into the perforated pipe.
- Reduced flows, achieved through the use of flow restrictors and low-flow faucets and fixtures, may be beneficial.
- Because of the seasonal high water table, the soil around the trenches might get saturated, reducing the soil’s ability to absorb wastewater.
- This may frequently be remedied by adding subsurface drains or curtain drains to intercept the water flow into the leach field region and to lower the water table in the immediate area around the drainage system.
- Likewise, see: In order to do a perc test, who should I hire?
- Is It Possible for Septic Systems to Last a Lifetime?
How Much Slope Do You Need for a Septic Line? Performing an Inspection on a Septic System When Is the Best Time to Take a Perc Test? Should I use a Sand Filter with my existing septic system? Examination of the WellSEPTIC SYSTEMView allSEPTIC SYSTEMarticles Return to the top of the page
Can A Septic Tank Cause Indoor Plumbing Problems?
Those who live in a home that is not linked to the municipal sewage system instead utilize a septic system to dispose of their waste. When homeowners understand how their septic system works, they are more likely to detect minor difficulties that may develop into major problems over time, prompting the need for emergency septic services. Residents in Gainesville should be aware that early signs of a septic system experiencing issues are frequently visible inside the home, according to Jones PlumbingSeptic Tank Service professionals.
How Does A Septic System Work?
An underground main sewer line connects drain pipes in your home to the septic tank in a domestic septic system, which is located beneath your property line. Solid waste settles in the bottom of the tank and grease accumulates at the top, resulting in a separation of wastewater according to matter. A drainage field is formed by the seepage of sewage water, which is then broken down by microorganisms. Over time, the sludge at the bottom of the tank builds and becomes a hazard. Regular septic tank servicing is required to avoid a full or overflowing tank, which can cause difficulties with the interior plumbing system if left unattended.
How Do Septic Tanks Affect Indoor Plumbing?
Whenever there are issues with a septic tank, the earliest signs of trouble generally arise in the plumbing system of the home or building. Some early indicators of septic tank difficulties include extended flushing of the toilets and poor draining in sinks and bathtubs, among other things. Water backing up into sinks, showers, and tubs is a common symptom of a clogged septic tank. Some homeowners may hear gurgling in their drainpipes or percolating sounds coming from their bathrooms as a result of this.
- The likelihood of a blockage in the indoor plumbing increasing if water is only backing up into one sink or toilet is greater than the opposite.
- Pouring boiling water down the drain or using a drain snake can assist clear less major obstructions.
- The system itself should be inspected by homeowners who feel their indoor plumbing problems are an indication of a failing septic system.
- Septic tank problems such as excessively lush plant growth or swampy conditions are indicative of a blocked or overflowing tank that is enabling waste to reach the drainfield.
Common Septic Tank Problems
Having a blockage in the inlet, outlet, or filter of your septic tank is the most typical septic tank problem that leads to indoor plumbing issues. As a result, you may require a septic tank pumping or filter replacement or cleaning, among other services.
Slow drainage and gurgling noises may indicate a clogged sewage vent, which may be repaired. If pipes get blocked or damaged as a result of tree roots or heavy machinery, more comprehensive septic tank repairs will be required in the future.
Septic System Maintenance
Regular septic system maintenance is essential in order to avoid costly issues down the road. A septic tank should be drained every two to three years, according to septic tank professionals in Gainesville, Florida. When dealing with bigger families, more frequent pumping may be required. In order to eliminate trash that has built up in the tank over time and to avoid obstructions, homeowners should have their Septic Tanks pumped on a regular basis. It is also a fantastic approach to uncover possible concerns before they become a problem.
Annual septic tank inspections are the most effective method of ensuring that a septic system is operating correctly.
How Does A Septic Tank Work? Learn How Septic Systems Treat Wastewater
Many homeowners are terrified by the thought of having a septic tank because they believe it would be difficult to repair and expensive to maintain in the future. With regular maintenance, a well-constructed septic system may survive for up to forty years. Knowing the ins and outs of your septic system is essential to getting the most out of it. We’ll go over the fundamentals, such as how a septic tank works, what it is, and how to maintain it so that it lasts as long as possible.
What is a Septic Tank?
Septic systems are considered unusual and out of date by many people. As many as one in every five American houses, particularly in rural regions, is equipped with an aseptic tank. A septic tank is a large underground tank that is used to store and treat sewage. It enables homes to securely dispose of wastewater from bathrooms, showers, dishwashing, and other sources by transporting it outside of the home. Septic tanks, as well as the machinery that supports them, are placed underground. For safety reasons, they are usually put at least 10 feet away from the home when possible.
The most common materials used to construct a septic tank are concrete and plastic.
Septic tanks are available in a variety of sizes to accommodate different sized residences.
What is a Septic Tank Used For?
The water that runs from your residence is frequently polluted, making it dangerous to drink or handle in any way. Bathing, cleaning dishes, and doing laundry all contribute to the production of polluted water. Septic tanks treat wastewater that goes through the system by the use of natural and mechanical processes, respectively. It doesn’t matter where it emanates from within the house, either.
In order to restore water to the earth, it must first be cleaned of undesired particles and organic materials. In this case, the role of your septic system is crucial. Septic systems are used to treat wastewater when there are no public sewer systems accessible.
How Does a Septic Tank Work?
Septic tanks function by allowing wastewater to rest and settle, which is a natural process. In a septic system, solid particles and sediment settle to the bottom, where they may be separated from the water. Bacteria eat away at the sludge over time, transforming it into more manageable components for human use. This also causes scum to be released, such as fats, greases, and oil. Scum rises to the surface of the water and collects there. Following the filtration of the sediments, the filtered liquid wastewater, also known as “effluent,” is discharged via perforated pipes.
These outlet pipes transport the water to a place known as the drainfield or leach field, depending on the region.
Finally, the wastewater percolates into our soil, where it is able to free itself of any harmful substances.
In human excrement, coliform bacteria that are harmful to the body can be discovered.
Septic Tank Design
Tanks are available in a variety of shapes and sizes. Depending on the number of bedrooms, soil condition, lot size, and other considerations, a household will choose one over the other. A septic system may be classified into several categories, according to the Environmental Protection Agency (EPA). The most prevalent of them are as follows:
- The term “standard septic tank” refers to a single or double-chamber tank that is located underground. a conventional septic system is a complete underground water treatment system in which the septic tank discharges onto a soil or gravel drainfield
- And Septic tank system that does not require excavation and instead makes use of linked subsurface chambers rather than an open drainfield. Drip Distribution System: A shallow septic system that uses drip tubing to disseminate sewage gently
- These devices operate similarly to a tiny sewage treatment plant, using oxygen to stimulate naturally occurring bacterial activity for the purpose of treatment. When it is impossible to bury a drainfield, such as in places with shallow soil or high groundwater, a mound septic system is used to properly route wastewater flow through elevated trenches. Pump-Chamber-Sand Filter System: This system circulates effluent from the tank to the pump chamber, where it percolates through the sand filter. Depending on the use, it can be put above or below ground. In the absence of a filter, all waste particles will be able to pass through easily and clog your pipes
- Method of Evapotranspiration: Rather than filtering wastewater through the soil, this system traps it in the drainfield using a watertight membrane, allowing it to evaporate. Constructed Wetland System: This environmentally friendly system mimics natural water treatment processes by directing wastewater to a wetland cell rather than a drainfield for screening and treatment. The use of a community septic system might occur when many home sites are near together and the septic tanks flow into a common drainfield.
Inside a Septic Tank
The most common configuration consists of a septic tank, a distribution box, a drain field, and a network of perforated pipes that connects the first and second tanks. There is a single main drainage pipe, also known as an input pipe, that connects the septic tank and the home. The water waste from your home passes through it and into the septic tank, where solid and liquid waste are separated from the liquid waste and disposed of separately. Nowadays, the majority of septic tanks are divided into two parts.
Both compartments are waterproof and are separated by a sturdy wall that prevents water from entering.
A T-shaped baffle, similar to the inlet and exit pipes, is used to prevent particles from entering.
The Septic System Treatment Process
When wastewater enters a treatment plant through an intake pipe, grease and oil float to the top of the water column, while solid waste and silt sink to the bottom. This is done in order to keep them out of the wastewater once it reaches the drainfield. Solids can clog the perforated pipes in the area, and oils can cause harm to the leached soil as they pass through. There is a healthy population of anaerobic bacteria in the soil underneath the septic tank, and these bacteria feed on and digest the organic waste.
Sludge and scum are prevented from exiting the septic tank and entering the drainfield by an outlet baffle at the other end of the system.
The drainfield is a shallow area of open ground near the home that filters untreated wastewater via rocks, mud, and sand in order to eliminate contaminants in a natural and environmentally friendly manner.
A good septic system is one that is hidden underneath and not visible.
Over each baffle, there are normally inspection openings, and most septic tanks also include a manhole access port, which enables for the pumping of the tank to take place. These access points are normally protected by a plastic cap with a diameter of approximately 4″.
What Does a Septic Tank Look Like?
From the exterior, an underground septic tank is typically characterized by the appearance of a huge metal or plastic box. These septic systems may typically be distinguished by the characteristic inspection pipes located on top of the box, which are often covered with green covers. The majority of tanks are equipped with one or two inspection pipes as well as bigger manhole covers for pumping. A vent pipe is used to expel the gases that have accumulated. Above-ground septic tanks have a distinctive appearance that distinguishes them from their underground counterparts.
Aside from that, they are often constructed of fiberglass, polymers, or some other weather-resistant material.
A network of tiny, perforated pipes connected to the outflow and reaching into the drainfield’s soil is also present.
This will be determined by your daily water use as well as the number of bedrooms in your home.
What Does a Septic Tank Do?
Designed to remove sediments and pollutants from water, septic tanks are often used in residential and commercial settings. Understanding what a septic tank accomplishes will help you better understand how to care for your septic system in the future. The majority of conventional septic tank systems consist of a septic tank, which is often a large, hidden rectangular or cylindrical vessel composed of cement, fiberglass, or polyethylene material. It is not uncommon for septic systems built before 1975 to have a single compartment and for those built after 1975 to have many compartments, according to industry standards.
Sewage from all plumbing connections is directed toward the septic tank, where heavy masses fall to the lowest point and bacterial activity produces digested slime and fumes as a result of the digestion process.
Septic Tank Clean Out: Don’t Abuse the System
It is necessary to clean your septic system on a regular basis in order to keep it in good working order. If you don’t, your drains may become blocked, you may notice smells, and your drain field may become backed up with water. Septic tank pumping should only be required every two to three years in a well functioning system. When you have your tank pumped, it eliminates sediments, which enhances the flow and efficiency of the wastewater treatment process overall. If you don’t know what you’re doing when performing system maintenance, it’s possible to cause damage to the system.
We recommend that you have your septic tank cleaned by a professional. This will assist you in ensuring that your septic tank is working at peak performance and will prevent toxins from accumulating in the system over time.
Don’t Use Additives
Inadvertently adding chemical and biological additives is one of the most typical maintenance blunders. There are several flushable pills on the market that claim to improve the performance of your septic system by speeding up the breakdown processing and adding extra bacteria. With the help of these substances, you will be able to cope with septic system failure. These have the potential to disrupt the delicate natural equilibrium in your tank.
Don’t Flush the System
When septic systems are flushed out too quickly, it can have an adverse effect on the bacteria that live there. It can also cause scum and sediments to be disturbed, increasing the likelihood that they will clog up system components.
Take Care of the Drainfield
During normal septic tank maintenance, it’s not only the tank that has to be taken into consideration; the drainfield is just as vital. It is not recommended that you construct a structure or plant anything with deep roots in the region. Avoid driving on the drainfield as much as possible since this might compress the soil and cause the effluent flow to become obstructed.
Don’t Overload the Septic System
When using a septic system, there are several things that should not be flushed down the drain. Organic waste and septic-safe tissue are the two types of waste that septic tanks can manage. The following are examples of things that might overflow your septic system:
- Toilet paper
- Diapers and sanitary goods
- Disposable wipes
- Paint and chemicals
- Cat litter
- Coffee grinds
- Fabric and apparel.
It’s always a good idea to double-check that anything is septic-safe before flushing it down the toilet. Though most toilet paper is septic safe, biodegradable toilet paper is preferred in order to avoid disturbing the important microorganisms. A clogged toilet or sewage forcing its way up through the leach field are all possible consequences of overburdening your system.
Hire the Best Plumbing Service and Get Your Waste Water TreatmentSystemInspection Done Today!
Septic tank inspections should be performed every two to three years, at the absolute least. This will be done by a professional during normal pumping. If, on the other hand, you detect indicators that your septic system is malfunctioning, you should schedule an inspection as soon as possible. A faulty system might result in untreated garbage being transported to locations where it does not belong. While it’s vital to understand how a septic tank works, homeowners should always seek expert assistance if they have any problems with their system.
A basic home inspection will often only give the septic tank a cursory scan, so it’s advisable to contact a professional to examine the system thoroughly before making a decision on whether or not to purchase a home.
- Septic tank inspection, Septic tank maintenance, Septic tank installation, Septic tank repair, Septic tank pumping are all services that are available.
From our offices to your home, we always put you front and foremost in all we do. Call now to schedule a free septic check with one of our septic contractors.