How Much To Upgrade Septic Tank With Bigger One? (Correct answer)

For homes with 4 bedrooms or more, you can expect the septic tank’s size to be 1500 gallons or larger. You can expect to pay between $1200 and $2000 for a larger septic tank. When most people think about septic system costs, they think about replacing a tank or installing a new one.

  • National average costs range from $500 to $5,000. The national average costs for a septic tank installation or to replace aging septic system depend on several factors. One in five homes in the United States relies on a septic system for wastewater management, according to the Environmental Protection Agency (EPA).

How do I increase the size of my septic tank?

The simplest way to add to your septic tank while remaining connected to existing sewer lines is to simply add an additional septic tank. This gives your home a larger wastewater capacity, and gives your septic system more time to treat the wastewater before draining.

Is a bigger septic tank better?

For instance, if your home has two occupants, you will require a small septic tank. On the other hand, if your property has more than five occupants, you will need a bigger septic tank to manage your wastewater more effectively and hygienically.

Do I need to upgrade my septic tank?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

What is considered a large septic tank?

Most residential septic tanks range in size from 750 gallons to 1,250 gallons. An average 3-bedroom home, less than 2500 square feet will probably require a 1000 gallon tank. Of course, all of this depends on the number of people living in the home and the amount of water and waste that will be put into the system.

What happens if your leach field is too small?

If drain field soil becomes compacted, then the very small pockets of air that lie between soil particles are eliminated and the aerobic bacteria can die. When these bacteria die off, they cannot clarify wastewater properly.

How often does a 1000 gallon septic tank need to be pumped?

For example, a 1,000 gallon septic tank, which is used by two people, should be pumped every 5.9 years. If there are eight people using a 1,000-gallon septic tank, it should be pumped every year.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Does shower water go to septic tank?

From your house to the tank: Most, but not all, septic systems operate via gravity to the septic tank. Each time a toilet is flushed, water is turned on or you take a shower, the water and waste flows via gravity through the plumbing system in your house and ends up in the septic tank.

Does heavy rain affect septic tank?

It is common to have a septic back up after or even during a heavy rain. Significant rainfall can quickly flood the ground around the soil absorption area (drainfield) leaving it saturated, making it impossible for water to flow out of your septic system.

Can you sell a house with an old septic tank?

If you’re selling a property with a septic tank, then you must be transparent with buyers about the fact the property uses a one and provide a detailed specification of the system. In fact, You are required by law to inform a buyer in writing about the presence of a septic tank.

Can you sell a house with a septic tank?

If you currently have a septic tank that discharges to surface water then the sale will trigger the requirement to replace or upgrade the system. Buyers should satisfy themselves that any system is in good working order and does not cause pollution.

How often should you pump your septic tank?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

How deep should a septic tank be?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

Learn how much it costs to Install a Septic Tank.

Septic tanks range in price from $3,157 to $10,367, or an average of $6,743. Installation of a conventional 1,000-gallon tank for a three-bedroom home might cost anywhere from $2,100 and $5,000. Materials range in price from $600 to $2,500, without labor. A comprehensive septic system, which includes a leach field (also known as a drain field), tank, and plumbing, can cost between $10,000 and $25,000 to install. A leach field installation might cost anywhere from $5,000 to $20,000, depending on the kind.

In the end, the cost of installing a septic tank is determined by the kind of system, the materials used, and the size of the tank.

This course will teach you about the several sorts of settings, such as conventional, drip irrigation, mound irrigation, evapotranspiration, recirculating sand, constructed wetland, and chambered irrigation.

Septic System Cost Estimator

Let’s run some numbers to see what the costs are. What part of the world are you in? What part of the world are you in?

National Average $6,743
Typical Range $3,157 – $10,367
Low End – High End $450 – $20,000

The cost information in this report is based on real project costs provided by 943 HomeAdvisor users.

New Septic System Cost

Most tanks and systems cost between $2,000 and $10,000 to install a new typical anaerobic septic system. Aerobic systems range in price from $8,000 to $20,000. Depending on the size of your property, the composition of the soil, and the level of the water table, you may even have to pay an extra $10,000 or more for an alternative, specialized drain or leach field. Septic systems are composed of three major components:

  • Septic tank: Either anaerobic (requiring no oxygen) or aerobic (requiring oxygen but more complicated but more efficient)
  • Water runs to a leach field after it has been cleaned and separated in the septic tank, where it will naturally drain through sand, gravel, and soil in a cleaning process before reaching the water table
  • Water table: Plumbing: A drainpipe to the tank, followed by another branching pipe to your field will be required.

Optional components include the following:

  • Some types of systems use a dose or pump tank, which pumps wastewater up into mounded or elevated leach fields and recycles the water in some cases. Pump for aeration: If your aquarium is equipped with an aerobic system, you’ll want an aerator to force oxygen into the tank.
Find Local Septic Tank Installers

The installation of a traditional anaerobic system typically costs between $3,000 and $8,000 on average. Anaerobic systems are often less expensive to build than aerobic systems, which are more complicated. However, because they are less effective at cleaning the tank, you will need a bigger leach field to accommodate the increased burden. An anaerobic septic system is a very basic system that consists of a pipe that runs from the home to the tank and a branching pipe that runs from the tank to the drain field, among other components.

Aerobic Septic System Cost

Aerobic systems, which are those that require oxygen to work properly, cost on average between $10,000 and $20,000 per system. If you’re moving from anaerobic to aerobic fermentation, you’ll almost certainly need a second tank, but the conversion will only cost you $5,000 to $10,000. Aerobic systems break down waste more effectively in the tank than anaerobic systems, allowing you to use a smaller drain field in many cases – which is ideal for properties with limited space. An aerobic wastewater system is a wastewater system that depends on aerobic bacteria (bacteria that thrive in the presence of oxygen) to break down trash in the tank.

You’ll need an aerator as well as an electrical circuit that connects to the system to complete the setup. Small, mounded, or speciality fields may necessitate the addition of a dose or pump tank to assist in pushing effluent (sewage or wastewater) upward or out in batches.

Get Quotes From Local Septic Tank Pros

Beyond the tank and leach field, there will be a few more costs to consider when creating your budget for the project. You may already have some of these costs included in your total project pricing, so make sure to get line-item prices on your estimate.

  • Excavation costs $1,200–$4,500
  • Building permits cost $400–$2,000
  • And a perc test costs $700–$1,300. Labor costs range from $1,500 to $4,000
  • The cost of septic tank material ranges between $500 and $2,000.
  • Plastic and polymer materials cost $500–$2,500
  • Concrete costs $700–$2,000
  • And fiberglass costs $1,200–$2,000.
  • 500: $500–$900
  • 750: $700–$1,200
  • 1,000: $900–$1,500
  • 1,200: $1,200–$1,600
  • 1,500: $1,500–$2,500
  • 2,000: $3,000–$4,000
  • 3,000: $4,500–$6,000
  • 5,000+: $7,500–$14,000
  • 500: $500–$900
  • 1,200: $1,200–$1,

Leach Field Cost

Installing a leach or drain field, which is a component of your septic system, can cost anywhere from $3,000 to $15,000 in total. The cost of a typical drain field ranges from $2,000 to $10,000. The drain field, also known as the leach field, is the section of the septic system that is responsible for returning wastewater to the soil. Most of the time, a flooded area in the yard or a strong stink of sewage on the property is the first symptom of a problem with the drainfield. It is possible that you may require further treatment for blocked or flooded fields, which would increase the cost of the drain field repair from $10,000 to $50,000.

Alternative Septic Systems Cost

When you have a tiny property, a high water table, high bedrock, poor soil, or just wish to utilize less space, an alternate septic system is a good choice.

Mound Septic System Cost

Installing a mound septic system can cost between $10,000 and $20,000 dollars. In places with high water tables, thin soil depths, or shallow bedrock, this is the most costly system to build; yet, it is frequently required. In order to create a drain field, it uses a raised mound of sand rather than digging into the soil. Its extra cost is a result of both the additional technology required to pump sewage upward into the mound and the materials and labor required to construct the mound in the first place.

Recirculating Sand Filter Septic System Cost

Sand filter septic systems range in price from $7,500 to $18,500. They can be built above or below ground depending on the situation. In order to disperse the wastewater in the ground, they employ a pump chamber to force the wastewater through a sand filter. The lining of the filter box is typically made of PVC. This is accomplished by pumping the effluent through the sand and returning it to the pump tank, where it is then disseminated throughout the ground.

Drip Septic System Cost

Drip systems range in price from $8,000 to $18,000, depending on the size and complexity. They operate in the same way as other systems, with the exception that they employ extensive drip tubing and a dose system. They deliver smaller doses over a shorter period of time, which is particularly effective in shallow soil depths. This method is more expensive than a standard system since it requires a dosage tank, a pump, and electrical power to operate.

Evapotranspiration System

Evapotranspiration systems range in price from $10,000 to $15,000 per system. In order to allow the liquid to evaporate from the top of an open-air tank, they employ a novel drain field configuration. They’re only usable in dry, arid areas with little rain or snow, thus they’re not recommended.

Built Wetland System

Built-in wetland systems range in price from $8,000 to $15,000, with the cost increasing if an aerobic tank is included. They are designed to mimic the natural cleansing process found in wetland ecosystems.

After passing through a wetland tank, where it is treated by microbes, plants, and bacteria, it is returned to the soil. The waste also has the effect of assisting the growth of wetland plants and the population of microbes.

Chambered System

Installation of chambered systems ranges from $5,000 to $12,000 dollars. They employ plastic perforated chambers surrounding pipes, which are frequently laid in sand, to keep them cool. Gravel is no longer required as a result of this. They are quick and simple to install, but they are more subject to crushing pressures, such as those caused by automobiles.

Septic Tank Replacement Cost

The cost of replacing a septic tank ranges from $3,000 to $10,000. From 30 to 40 years, you may anticipate your system to serve you well. The system may crack or corrode as a result of the failure and the resulting contamination of groundwater with toxic waste is an issue. When this occurs, the well water may get polluted, the yard may become marshy, and the septic system may become inoperable or fail completely. Here’s a breakdown of the various components of a septic tank, along with an estimate of their usual costs: Replacement of a septic tank pump costs between $800 and $1,400.

Replacement of the filter costs between $230 and $280.

Drain Field Replacement Cost: $7,500.

Septic System Maintenance Costs

It is essential that you pump and clean your septic tank at least once a year. In addition, you should have it inspected at least once every three years. The proper maintenance of your septic tank will save you money in the long term, and it will also help you avoid potentially hazardous situations. The Environmental Protection Agency (EPA) suggests the following steps to keep your septic system in good working order:

Inspect and Pump Your Septic Frequently

Typically, the cost of septic tank pumping runs from $300 to $550, or around $0.30 per gallon – most septic tanks have capacities between 600 and 2,000 gallons. Every three to five years, you should have your septic tank inspected and pumped by a professional. If you have a bigger home (with more than three bedrooms) and you tend to use a lot of water, you should try to get it pumped at least once every three years. An checkup of a septic system might cost anything from $100 to $900. Your septic inspector will do a visual inspection of the system.

  • The typical cost of septic tank pumping ranges from $300 to $550, or approximately $0.30 per gallon — most septic tanks hold between 600 and 2,000 gallons of wastewater. Every three to five years, you should have a professional inspect and pump your septic tank. It is recommended that you get your water pumped at least once every three years if you live in a bigger home (with more than three bedrooms). An checkup of a septic system can cost anywhere from $100 to $900 dollars. Septic system visual inspection is performed by your septic inspector. You may spend an additional $250 to $900 on a camera check of the lines, but this is only essential if your drains are running slowly and you can’t figure out what’s causing the issue.
See also:  What Is Used For Dye In Septic Tank?

Use Household Water Efficiently

A toilet that leaks or runs continuously might waste as much as 200 gallons of water per day, although the average family consumes just 70 gallons of water. Take, for example, high-efficiency toilets, which use 1.6 gallons or less of water per flush or less. The use of new, high-efficiency washing machines and showerheads can also help to reduce water waste, which will relieve the strain on your septic system.

Properly Dispose of Your Waste

Your septic system is responsible for disposing of everything that goes down your drains and toilets.

One simple rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless it is absolutely necessary. That implies you should never flush the following items down the toilet or drop them down the sink drain:

  • Cooking grease or oil, baby wipes or wet wipes, dental floss, diapers, feminine hygiene products, cigarettes, cat litter, and paper towels are all examples of items that fall into this category.

Maintain Your Drainfield

The drainfield of your septic system is a component of the system that removes waste from the septic’s liquid. You should take steps to keep it in good condition, such as:

  • Never park or drive your vehicle on your drainfield. Don’t ever put trees near your drainage system. Maintaining a safe distance between your drainfield and roof drains, sump pumps, and other drainage equipment
Get in Touch With Septic Tank Installers Near You

A septic tank or septic pump tank can range in price from $350 to $14,000, depending on the material used and the size of the tank. In most home situations, you won’t have to spend more than $3,000 on the tank’s actual construction. The majority of big, high-priced units are intended for use in apartment buildings or as part of a communal sewage system.

Concrete Septic Tank Cost

Concrete tanks range in price from $700 to $2,000. The total cost of installation ranges from $2,300 to $6,500. They’re one of the most frequently encountered types of installation. Despite the fact that they are susceptible to cracking and separation, they are typically durable for several decades. It’s critical to have it carefully inspected on a regular basis for cracks and runoff, among other things. Inspections and regular cleanings will help to extend its useful life. Your professional can tell you how frequently you should get it inspected, but it’s normally every one to three years.

Plastic and Poly Septic Tank Prices

Septic tanks made of plastic range in price from $500 to $2,500 on average, not counting installation costs. Plastic is a long-lasting, lightweight, and reasonably priced building material. They do not crack as easily as concrete and do not rust. Because of their small weight, plastics are more susceptible to harm during the installation process.

Fiberglass Septic Tank Prices

Fiberglass septic tanks are typically priced between $1,200 and $2,000, not including installation. Fiberglass does not split or rust readily, but it is prone to damage during the installation process, much like plastic. However, because of its lighter weight, it is more prone to structural damage, and the tanks themselves can move in the soil.

Steel

It’s unlikely that you’ll ever see a new steel tank constructed. They will rust or corrode with time, no matter how well-made they are at the time. As a result, they are not permitted by many local building codes, and you will only see them in existing installations. Steel is not a long-lasting material in the earth, and it is the least preferred.

Labor Costs to Install a Septic System

The cost of labor accounts for 50 percent to 70 percent of your overall expenses. Labor is typically more expensive than the tank itself in a normal installation, making it the most expensive option. For example, while the size required for a 3 to 4-bedroom home may cost between $600 and $1,100, the labor to install it might cost anywhere between $1,500 and $4,000.

Compare Quotes From Local Pros

Here is a breakdown of how much septic tanks cost in different parts of the country. Massachusetts:$9,700 California:$4,500 Florida:$5,300 Texas:$8,000 $5,600 in New York City Colorado:$7,800 Idaho:$10,000

DIY vs. Hire a Septic System Pro

A look at how much septic tanks cost in different parts of the country is provided below. Massachusetts:$9,700 California:$4,500 Florida:$5,300 Texas:$8,000 $5,600 in New York Colorado:$7,800 Idaho:$10,000

FAQs

A septic tank has an average lifespan of 20 to 30 years, however it may live anywhere from 14 to 40 years, depending on the following factors:

  • In general, a septic tank will last between 20 and 30 years, however it may last anywhere from 14 to 40 years, depending on the following factors:

What are the signs I need a new septic tank?

There are a few indicators that it is time to replace your septic tank. Among these are:Unpleasant odors:If your septic tank is overflowing with solid waste, you may be dealing with a clogged drain field or a broken pipe or septic system.Slow draining:A full septic tank will cause pipes to drain more slowly.Paths of vibrant grass:A wastewater leak can actually fertilize grass, causing it to grow thicker and greener over your sewer line.Paths of vibrant grass:A wastewater In order to be sure that your septic system is capable of handling any new additions, check with your local water authority.Nearby water pollution: A septic tank leak can result in wastewater contamination that can deposit nitrate, nitrite, or coliform bacteria in nearby water sources.

Whether these bacteria are identified in your area, you should inspect your septic system to determine if it is the source of the problem.Old age:If your septic system has reached the end of its useful life, it is time to replace it.

Does homeowners insurance cover septic systems?

Many unforeseen and abrupt repairs to septic tanks are covered by homeowners’ insurance policies. They do not, however, often cover harm caused by a failure to perform routine maintenance. Make certain that you are pumping and cleaning it on a yearly basis.

How much do septic system repairs cost?

Repairing a septic system can cost anything from $600 to $3,000. Most tank repairs and replacement parts cost less than $1500 for each type of repair or replacement part mentioned below. Leach fields range in price from $2,000 to $20,000.

  • Tank Pumps cost between $800 and $1,500. A septic tank that is placed below the drain field may necessitate the installation of a pump to transport wastewater to the drain field. Pumping costs between $300 and $600 per year. Pumping is required to remove solid waste from even a perfectly functioning system every two or three years, even if it is in good working order. Tank Lids cost between $100 and $300 to purchase and install. If you purchase the lid and attach it yourself, it will cost you between $50 and $150
  • Tank Lid Risers range in price from $300 to $1,000. Deeply submerged tanks can have their lids raised to the surface by using these devices.
Still Have Questions About Septic Tanks?

A Quick Look at Septic Tank Prices

  • Total cost: $3,900 on average
  • $1,500 to $5,000 on a sliding scale
  • Anaerobic septic tanks cost between $2,000 and $5,000
  • Aerobic septic tanks cost between $10,000 and $20,000
  • Gravity septic tanks cost between $1,500 and $4,000
  • Mound septic tanks cost between $10,000 and $20,000
  • Chamber septic tanks cost between $1,500 and $5,000
  • Conventional septic tanks cost between $2,000 and $5,000.

The wastewater generated by your household is teeming with potentially harmful germs. In order to properly dispose of waste and prevent it from backing up into your sinks and toilets, you must ensure that your septic tank is in good working condition. This Might Also Be of Interest to You: What Is the Difference Between a Septic System and a Sewer System? Everything you need to know about septic tank replacement, including how much it will cost, can be found in this article.

What Is a Septic Tank?

A septic tank is an underground chamber that is used to treat residential wastewater to a modest degree. It is intended to store wastewater for an extended period of time, allowing particles to settle to the bottom and oil and grease to float to the surface. After that, the liquid waste is filtered away.

How Much Does It Cost to Install a Septic Tank?

In most cases, a new septic tank system will cost you around $3,900 to install. It costs between $1,500 and $5,000 to install a typical 1,250-gallon tank, which is the perfect size for a three- or four-bedroom house. This price includes the tank itself, which ranges in price from $600 to $2,100 or more depending on the size and type. Workman’s compensation is included in the price of the installation and often ranges from $1,500 to $4,000.

Types of Septic Tank Systems

Septic tank installation and replacement costs are heavily influenced by the type of system that you select to use. Tanks come in a variety of shapes and sizes. Here are a few examples:

Anaerobic Septic System

Anaerobic systems are a popular alternative for many homes since they don’t require any additional electricity or chemicals to function properly. Anaerobic systems include microorganisms that do not require oxygen to exist and hence are called anaerobic systems.

Solid waste is broken down by bacteria, and any remaining liquid waste is piped out and distributed beneath the surface of the soil. The garbage is naturally recycled when the water seeps into the ground and returns to the environment. The installation of these devices is between $2,000 and $5,000.

Aerobic Septic System

Aerobic systems, in contrast to anaerobic systems, make use of microorganisms that do not require oxygen to live. To activate the bacteria in the tank, oxygen is injected into it, and the bacteria then feed on the solid waste. Aerobic systems perform effectively in soils that are unsuitable for other systems and in areas where the groundwater table is elevated. It is an excellent choice for residences that are close to a body of water. Aerobic systems are more costly to install than anaerobic ones.

Gravity Septic System

Gravity septic systems employ gravity to filter and move water through the system. They must be put on a mild slope in order to allow water to flow without the use of a pump. The cost of installation ranges from $1,500 to $4,000.

Conventional Septic System

A standard septic system is comprised of a septic tank and a trench that serves as a drain field for the collection of waste. The trench is built on stone or gravel and is designed to allow water to move through it easily. In order to prevent sand or dirt from contaminating the clean soil, geofabric is laid over the top of the trench and secured in place. In order to function properly, a conventional septic system requires a large amount of space. The installation of these devices is between $2,000 and $5,000.

Mound Septic System

If your groundwater table is close to the surface, a mound septic system is the most appropriate option for your situation. An area for the septic system is prepared, and a sand mound is built to allow effluent from the tank to be pumped into the mound in modest amounts. The sand then acts as a filter, preventing the water from reaching the soil and groundwater. This design necessitates a large amount of floor space. They’re also expensive to install since a sand mound needs to be built before they can be utilized.

Chamber Septic System

Chamber septic systems have lately gained popularity as an alternative to traditional septic systems. They are similar to conventional systems, with the exception that plastic chambers, rather than gravel, are used in the drain field. These are less difficult to build and have a lower carbon footprint. The cost of installing them ranges from $1,500 to $5,000.

Septic Tank Materials

Another aspect that influences cost is the type of material used to construct your septic tank. The following are some of the most often seen materials:

Concrete

Concrete septic tanks are the most prevalent form of septic tank because they are extremely long-lasting and reliable. They can last for 20 to 30 years if they are properly maintained. Concrete, on the other hand, may crack over time. When concrete is reinforced with rebar, the strength of the concrete is increased when subjected to pressure. Because of its weight, installation is more difficult and necessitates the use of specialized equipment. The cost of a typical-sized concrete tank ranges from $720 to $2,050 dollars.

Fiberglass

Fiberglass does not deteriorate when utilized underground, and because it is nonporous, it will not support the formation of algae.

Because of the tank’s modest weight, it is easy to install. You won’t have to worry about cracking since, unlike concrete, it will not expand or shrink as the weather changes. The typical cost of a fiberglass tank is between $1,600 and $2,000.

Plastic

Tanks made of plastic are lightweight and simple to install. They’re also fairly long-lasting. Plastic tanks range in price from $830 to $1,400 on average, depending on the kind.

Steel

In spite of steel’s strength and durability, septic tanks built of steel are susceptible to rust and collapse if not properly maintained. As a result, several municipal governments have tightened their restrictions in order to discourage their usage. Typically, you’ll discover them in regions where the system was already in operation. If you are able to have one installed, they range in price from $900 to $9,900.

What Size Septic Tank Do You Need?

The size of your septic tank is typically determined by the number of bedrooms in your house. This is used to calculate the amount of water that will flow through the system on a daily basis. In general, the expense of a system increases in direct proportion to its size.

Two Bedrooms

A septic system with a minimum of a 750-gallon septic tank is required for a two-bedroom residence. However, in many localities, a 1,000-gallon tank is the least capacity that may be accommodated.

Three Bedrooms

A minimum of a 1,000-gallon water tank is required for a three-bedroom residence, which handles around 360 gallons of water each day on a daily basis.

Four Bedrooms

A bigger tank, with a minimum volume of 1,250 gallons, is required for a four-bedroom residence. It is capable of handling around 480 to 600 gallons of water each day. Additional Related Articles:

  • How to keep the cost of septic tank pumping to a bare minimum
  • 3 Symptoms of Sewer and Septic System Problems
  • Do you have a clogged sewer line? Here’s What You Should Do
  • Water Sewer Line Repair: Do It Yourself or Hire a Professional
  • Listed below are 15 common plumbing problems that every homeowner should be aware of.
See also:  How Does A Septic Tank Overflow Backup? (Solution found)

Septic Tank Repair Costs

It’s conceivable that only a certain component of your septic tank has to be replaced rather than the complete tank. Repairs and replacement parts can be purchased for a fraction of the cost of a complete system replacement. The following are some of the most often seen repairs:

Drain Field

Drain fields can get overloaded and flood, resulting in sewage backing up into toilets and sinks. The cost of replacing a drain or leach field ranges from $3,500 to $11,000.

Tank Pump

A replacement septic tank pump typically costs between $500 and $1,200.

Tank Filter

It is the most typical type of filter change that is performed by homeowners. It typically costs between $230 and $280.

Tank Lid

Concrete coverings and steel lids may break and corrode as a result of exposure to the elements. In most cases, you can repair a septic tank lid on your own for about $35 and $60. In most cases, having it changed by a professional is more expensive.

Tank Baffle

The baffle is responsible for directing wastewater through the septic tank. A replacement baffle piece will cost between $23 and $44 dollars.

Additional Factors to Consider

A septic tank can be built either below or above ground, depending on your preferences. Because of the amount of excavating and footing preparation required, installing a tank underground is a pricey endeavor. Underground septic tanks necessitate the construction of a drain field that can accommodate a soakaway. In addition, because the soakaway allows for part of the wastewater to drain into the ground, the tank will require less emptying over time. Over time, this might result in a reduction in your expenditure.

Some demand that an inspector check and approve the site, which might result in a fee being charged to the homeowner. Depending on your state, septic tank licenses may be required to be renewed, but in most cases, you will be required to pay renewal costs when your permission expires.

How Long Does a Septic Tank Last?

The lifespan of a septic tank varies based on the material used and the type of system used. The lifespan of a septic tank might be reduced if the tank becomes clogged due to roots or floods from groundwater. Septic systems have a lifespan of 15 to 20 years on average. Maintaining your septic tank on a regular basis is the most effective approach to extend its life. Keep in mind that maintaining your tank entails more than just draining out the contents; it’s also crucial to have a professional evaluate your tank on a regular basis and perform routine maintenance.

In the event that you have a plan in place, you can call our 24-hour repair hotline whenever a covered problem arises.

How Much Does a New Septic Tank System Cost?

The average cost of a new septic tank system ranges between $3,060 and $9,810 dollars. While high-end systems can cost up to $20,000, entry-level systems can be purchased for as little as $465. Get quotes from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. Simply simply, trash is an unavoidable component of everyday existence. Septic tanks perform the dirty work for you, and they’re not particularly attractive. Anaerobic septic systems, which are the most common type, cost between $2,000 and $10,000.

Everything from the size of your property to its soil type and water table depth will determine which option is ideal for you.

How Much Does a New Septic Tank System Cost Near You?

In general, the cost of a new septic tank system is $6,420 on the national level, while particular costs vary from state to state depending on a variety of criteria. As a starting point, each state has its own set of fees and requirements for obtaining building permits and licenses. Before starting a septic tank project, be sure you understand the requirements in your region. The cost of a septic system varies from region to region as a result of variations in soil content across the country.

Septic tank system costs are approximately $3,000 in areas with sandy soil due to the lower labor and material costs associated with well-drained soils in these locations.

As a result, costs in New York, Washington, and Pennsylvania tend to be higher than in other states.

Septic Tank System Cost Breakdown

The total cost of installing a septic system will ultimately be determined by three factors: the materials and labor required to complete the installation, as well as the cost of digging a leach field on your property.

Materials

Concrete, fiberglass, and plastic are some of the most often used materials in septic tank systems. Concrete tanks are the most commonly used because of their longevity; with regular care, they may survive for up to 30 years or more. Concrete septic tanks typically cost between $700 and $2,000 on average. Plastic septic tanks are generally affordable, ranging in price from $500 to $2,500 per tank. On the other side, fiberglass tanks are more costly, ranging from $1,200 to $2,000 per tank.

Labor

It is possible that labor costs will vary by region and will be dependent on the size and materials used in the new septic tank system. However, in most cases, labor costs account for 50 percent to 70 percent of the total cost of a septic tank system installation. Even though installation is more expensive than purchasing the tank alone, it is well worth it if you do not have the time or resources to undertake yet another home improvement project at this point in your life. Make certain that you and your contractor or plumber go over all of the specifics.

Additionally, construction permits, which normally cost between $400 and $2,000, and perc tests, which cost between $700 and $1,300 on average, are additional expenses that may or may not be included in your septic tank installation prices.

Leach Field

Leach fields, which are a type of trench, are used in conjunction with septic tank systems to collect and treat wastewater. It is the component of your septic system that returns the wastewater to the earth, often known as a leach field or drain field. Leach fields range in price from $2,000 to $10,000. Photo courtesy of Natalia / Adobe Stock

How Much Does a New Septic Tank System Cost by Type?

Each type of septic system has its own set of advantages and disadvantages. Even though anaerobic systems require little maintenance, they are not suitable for use on smaller parcels of land. Anaerobic systems, on the other hand, can function well in small spaces but necessitate additional effort.

Anaerobic

Septic tanks can be classified as either anaerobic (requiring no oxygen) or aerobic (requiring oxygen). Anaerobic systems, which are more frequent, cost between $3,000 and $8,000 on average, according to the manufacturer. They are often less expensive to install than aerobic systems, but they are less efficient and need a bigger leach field than aerobic systems. In an anaerobic septic system, a pipe connects the home to the septic tank, and another pipe connects the septic tank to the leach field, where the waste is disposed.

This type of system does not require any additional electricity or chemicals, which makes it a popular choice among homeowners.

Aerobic

Aerobic septic systems make use of oxygen that is fed into the tank to activate bacteria that feed on the solid waste in the tank. These systems are more expensive than anaerobic systems, costing between $10,000 and $20,000, but they are more efficient and may be used effectively on smaller sites. In contrast to anaerobic systems, they require more electricity to function well.

Connecting it to a backup power generator will guarantee that everything continues to function correctly in the event of a power loss. In any other case, aerobic systems can be connected to the main power supply on your home.

How Much Does a New Septic Tank Cost by Style?

The size and location of your property will play a role in determining which type of septic tank system is best for your needs. The mound or sand filter aerobic septic tank systems are recommended for smaller properties, while those with greater room have a wider range of alternatives.

Mound

Expect to spend more money if you choose a mound septic system, which may cost between $10,000 and $20,000 to install. A sand mound is constructed on top of the septic system region to collect wastewater that has been pumped out of the tank. Water is filtered via the sand before it enters the soil and groundwater. Even though these systems are costly, they are important in locations where the water table is high.

Sand Filter

Sand filter septic systems employ a pump to force wastewater through a sand filter at a low pressure before it is released into the soil or groundwater, effectively treating and removing nutrients from the wastewater. Despite the fact that nutrients such as phosphorus and nitrogen are naturally found in waste, when they accumulate in surface water, they can degrade water quality and cause aquatic ecosystem damage. They range in price from $7,000 to $18,000 and may be constructed either above or below ground.

These systems are most effective in locations with high water tables or in areas where there are bodies of water nearby.

Chamber

Chamber septic systems are identical to conventional systems, except that they employ plastic chambers in the leach field instead of gravel to collect the waste. They range in price from $5,000 to $12,000 to install. Chamber septic systems are excellent solutions for sites with varying input quantities, such as vacation homes or rental properties. You should avoid placing it near your driveway or parking area if you choose this type since driving over it might cause considerable (and stinky) harm.

Drip

Drainage systems that employ drip tubing and a dosing device to release smaller, scheduled dosages of waste on a regular basis are called drip septic systems. They are particularly effective in soils with a short depth. It takes more components to install a drip system than it does to install a conventional system, such as a dosing tank or a pump, and it can cost anywhere from $8,000 to $18,000, depending on the size of the system.

Evapotranspiration

Evapotranspiration septic systems range in price from $10,000 to $15,000 and are particularly useful in arid climates and areas with shallow soil. They have special leach fields that allow effluent to evaporate from the top of an open-air tank, which is not common in other tanks.

If you reside in an area where there is a potential of snow or rain, an evapotranspiration septic system should be avoided at all costs. The dampness might eventually cause them to collapse, and the repair process for a septic tank is not particularly attractive.

Built Wetland

As you may have guessed, constructed wetland septic systems are designed to replicate the natural water treatment process found in wetlands. Water is treated in a wetland tank by microbes, plants, and bacteria before being released back into the environment. As a result, the waste promotes the growth of plants and bacteria. The cost of these environmentally friendly systems ranges from $5,000 to $12,000.

What Factors Influence the Cost of a New Septic Tank System?

Several factors influence the cost of a septic tank installation project. In general, costs rise as the size of the organization grows. If landscaping and permits are necessary for the installation of your septic tank, you should budget an extra $600 at the very least. The sort of material you choose will also have an impact on the price, with plastic being very inexpensive when compared to concrete. Furthermore, if you choose a more customized design over a stock model, you will be responsible for the additional labor costs.

As a result, the amount you pay will be determined by the location of your home as well as the soil type that surrounds your property.

FAQs About Septic Tank Systems

A septic system that has been poorly built can cause serious difficulties, such as water contamination and structural damage to your property. Repairs to a septic system are not inexpensive. Because of the high level of danger involved in constructing septic tanks, this process should be left to the professionals. Call around and talk about your requirements (as well as your budget) with a number of septic tank businesses in your region to find the ideal match.

What should I consider when installing a septic tank system?

A septic tank is an essential component of any home. Damage to your property as a result of structural failure or leaks may be costly, as well as dangerous to human and environmental health. It’s possible that the unpleasantness will even compel you to check into a motel for the night. Prior to establishing your septic tank system, take the following factors into consideration:

  • Soil type
  • Landscaping
  • Structural hazards (avoid places near cars or heavy machinery)
  • The size of the property
  • The size of the septic tank
  • Future maintenance
  • And the location of the tank

What other projects should I do at the same time?

Excavation is frequently required when installing a septic tank system (unless you opt for an above-ground tank). Once the excavators have broken ground, you may proceed with further subterranean projects that will save you time and money in the long run, such as:

  • Establish underground utilities and construct a retaining wall before beginning work on the sprinkler system.

Septic Tank Installation and Replacement Cost

The typical cost in the United States ranges from $500 to $5,000. The national average cost of a septic tank installation or the cost of replacing an aging septic system is dependent on a number of different variables.

Septic Tank Installation Average Costs
National Minimum Cost $500
National Maximum Cost $5000
National Average Cost $1500

According to the Environmental Protection Agency, one in every five residences in the United States relies on a septic system for wastewater management (EPA). In the case of septic systems, you may have a septic system for your home alone, or you may be connected to a communal system that services a small number of homes. Untreated wastewater created by a house or company is treated on site by a septic system, which is an on-site treatment system. Sewage lines convey wastewater from your shower, toilet, sinks, clothes washer, and trash disposal away from your home and into a septic tank buried in your yard.

Solids are separated from floatable debris in the septic tank, and the leftover liquid drains from the tank through a series of perforated tubes and onto a drain field or leach field after being separated in the tank.

The usage of septic systems is popular in rural regions that do not have access to a centralized municipal sewer system.

Tank capacity ranges from less than 1,000 gallons to more than 2,000 gallons, with the size of the tank determined by the amount of water you use on a daily basis.

Condos, apartments, residences, business spaces, and other types of structures might benefit from septic system installation or replacement services.

What’s in this cost guide?

  • Soil type
  • Tank size and kind
  • Equipment
  • Installation
  • Maintenance
  • Lift station
  • And more. Septic systems that are not conventional
  • How septic tanks function
  • Signs that you need to upgrade your system
  • How to hire a professional
See also:  How To Find Septic Tank Valve?

Alternative septic systems

Species of soil; tank size and tank type; equipment installation and maintenance; lift station; Septic systems that are non-conventional Septic tanks and the way they function; A list of warning signs that your system needs to be replaced; What to look for when hiring a specialist;

Signs you need a new system

Anyone would not want sewage water rising up through their front yard on one of the hottest days of the summer season (or even on the coldest day of winter). Waterborne pathogens such as protozoa, bacteria (such as E. coli), and viruses may be spread through fecal matter, making wastewater not just stinking and disgusting, but also potentially deadly. It is possible for unclean wastewater to drain through the soil and pollute the water you and your friends and neighbors drink if your septic system is leaky, overwhelmed, or otherwise compromised.

Knowing what indicators to look for might help you catch an issue before it becomes a major problem.

This includes having your septic tank pumped out by a professional every three to five years.

Other indicators may indicate that it is necessary to contact a septic system specialist as soon as possible to either repair or replace the system.

How Much Does a Septic Tank Cost? (2022)

The cost of replacing a septic tank typically ranges from approximately $3,000 to $10,000, depending on the type of tank your home requires, the size of your home, and the difficulty of the installation process. Because of these considerations, septic tank costs can vary widely, and a complete septic system can be significantly more expensive than simply replacing a tank. Doing your research is a good way to ensure that you’re getting the best deal possible. When you have the appropriate knowledge, you’ll be prepared for what to expect and what reasonable rates for repairs and replacements look like when you begin making phone calls and getting estimates for your vehicle.

What is a septic tank?

It is an underground structure that cleanses tainted water that has been discharged from your residence. These tanks are often constructed of concrete, fiberglass, or polyethylene, and they are a component of a larger septic system that transports wastewater to the tank and then releases it when it has been properly treated. Connecting to a septic tank can be less expensive than connecting to a sewage system, and they are frequently more environmentally friendly. However, they can necessitate more upkeep and greater caution when it comes to what you flush down the toilet.

You may have the option of choosing between a septic system and an underground shared sewer system when building a new home, but most homeowners opt to keep the system that was installed when their home was constructed.

How does a septic tank system work?

Septic tanks, in general, work by removing floatable stuff (such as oil) and solids from your home’s wastewater before discharging the remaining treated water into either the soil, sand, organic matter, wetlands, or other media, depending on the situation. The intricacies of how each form of system operates, on the other hand, will differ. An uncomplicated septic system is one in which both grey water and blackwater from your home drain into a holding tank. After a period of time, solids settle to the bottom of the tank while fats, oils, and grease float to the surface, forming scum.

Afterward, the scum and sludge are removed from the wastewater, and the treated water is discharged into the drainfield for further filtering and treatment.

Water is then continuously filtered as it travels downhill through the earth before reaching the groundwater.

Types of septic systems

There are many different types of septic systems, but the two most common are as follows:

  • Underground water treatment systems that use conventional (anaerobic) methods: These water treatment systems strain effluent (treated water) through stone or gravel in a drainfield. They’re normally best suited for single-family houses, and they’ll run you anywhere from $3,000 to $8,000 on average. Aerobic systems: These units increase the amount of oxygen in the tank, which accelerates the decomposition of organic waste. They can be utilized in situations when traditional systems may be ineffective, but they are more expensive, costing between $10,000 and $20,000 since they are more complicated.

Alternative system configurations include the following:

  • Chamber systems: These systems are an alternative to traditional (anaerobic) systems that do not require the use of gravel. They’re less difficult to construct and are better suited for places with higher water tables. The cost of installing a chamber system is between $5,000 and $12,000
  • Drip distribution systems (DDS): A DDS requires a secondary unit to retain wastewater once it has exited the septic tank, hence reducing the quantity of wastewater that may be discharged from the tank. The advantage is that it reduces the amount of dirt required in the drain field. A drip distribution system typically costs between $8,000 and $18,000
  • However, the price might vary. Mound systems: If the drainage field is required to be elevated above the tank, a mound system will be necessary. The wastewater is pushed up to the drain field by a pump tank, which means that this system requires more electricity and requires more maintenance on average. They range in price from $10,000 to $20,000
  • When your property is located on a high water table, this sort of system may be the best option for you. Recirculating sand filter systems A pump moves the effluent to a sand filtering system, where it is treated to remove the majority of toxins before it reaches the soil. It is estimated that the cost of these systems will range between $7,000 and $18,000. Evapotranspiration Systems: These systems are really only for persons who live in dry locations. The effluent evaporates into the atmosphere and never reaches the land or groundwater in this location. They cost between $10,000 and $15,000 to install
  • Constructed wetland systems: These systems are designed to look and function like natural wetlands. They require more area in order to function correctly, but the effluent is fully filtered. They range in price from $8,000 to $15,000, with costs increasing if you choose to install an aerobic tank.

Your tastes, household size, soil conditions, and property characteristics will all have an impact on which option is best for you.

Signs your septic tank is full

If you detect any of the following signs around your property, it is possible that your septic tank is either full or damaged:

  • Drains take a long time to drain
  • An inoperable or slow-flushing toilet
  • A toilet that won’t flush at all
  • The sound of gurgling after flushing a toilet or turning on the water The smell of sewage in the yard
  • It is important to have a lush grass, especially surrounding your septic tank. a puddle of water on the lawn

Any of these indicators might indicate that something is wrong with your septic tank, but there is a significant difference between a damaged tank and a tank that is overflowing with waste. Pumping may be used to empty a clogged septic tank, and it should only cost you $300 to $600 to do so. A faulty septic tank, on the other hand, will require either repair or replacement, which will almost always result in a higher financial outlay.

How much does it cost to repair a septic tank?

If your tank isn’t functioning properly, you could be looking at a $1,500 bill for repairs. However, it is possible that the problem is not with the tank itself, but with another component of the septic system. It all boils down to whatever portion of the system is malfunctioning:

  • Pump repairs might cost anything from $250 and $400. The cost of replacing your filter will be in the $200 to $300 area. Repairing baffles can cost anywhere from $100 to $900. Septic line repairs typically cost roughly $1,500, but it is not uncommon for them to cost as much as $4,000 in some cases.

Generally speaking, if you can get your septic tank or system fixed while still getting many years out of it, that is the most advantageous alternative. Not all issues, on the other hand, can be resolved. Septic tank professionals should evaluate the following factors when advising you on whether repair or replacement is the best course of action for your home:

  • Are puddles developing in a short period of time? Ponds in the yard aren’t usually a big deal, at least not in the long run. Puddles in the yard that form fast over night, on the other hand, are an entirely different story. The presence of puddles shows that the septic tank is nearly full, but it might also signal that there is a problem with the pipes or with the leach field, as well. The presence of large puddles often indicates a more serious problem, such as a damaged tank that would necessitate tank replacement. What is the size of your family? Septic tanks that are greater in size are required for larger homes. A bigger tank that can accommodate your growing family may be a smart choice if your home has increased over the years but your tank has not. How often do you find yourself in need of repairs? While a single repair isn’t a major concern, when repairs become more frequent, it’s time to take stock of your situation. A faulty septic system is almost certainly on its way out, which means you’ll have to pay to get it replaced.

Whether you’re repairing or replacing your unit, it’s important to remember that if your septic tank is still under warranty, you may expect to save a significant amount of money on your out-of-pocket expenditures. While some new septic tanks come with warranties from the manufacturer, a home warranty may be available to cover older units as well if they have been neglected.

However, should something go wrong with your septic tank, you may only be required to pay a modest service charge before your warranty provider covers the remainder of the cost of the repair or replacement.

How much does it cost to replace a septic tank?

A single-family home’s septic tank will cost between $3,000 and $10,000 to repair, depending on the situation. However, the price of your septic tank and the cost of installation are the two numbers that have the greatest impact on your overall cost. The cost of a septic tank varies depending on the kind and size of the tank in question. Unless you want to go bigger to accommodate future growth, the size of your tank is usually determined by the size of your household. There isn’t much flexibility there.

  • Concrete tanks: The cost of a concrete tank before construction might range from $700 to $2,000
  • Tanks made of fiberglass: A fiberglass tank can cost anywhere between $1,200 and $2,000 before installation. The cost of a polyethylene (plastic) tank is the most variable option, ranging from $500 to $2,500 before installation
  • However, this is the least expensive option.

The use of steel tanks is also an option, but they are less common and more susceptible to rusting.

How much does it cost to install a septic system?

However, steel tanks are less prevalent and more prone to corrosion than plastic tanks.

  • Perc test: A perc test analyzes the ability of your soil to absorb and filter water in a given amount of time. It entails the technician digging a 2- to 3-foot hole and pouring water into it to see how quickly the water disappears. A perc test will cost you anything from $750 and $1,850. Permits for construction: The cost of obtaining a construction permit varies from municipality to municipality. They typically cost between $400 and $2,250, but you may pay more if you choose to install an alternative septic system or if you live in a high-priced neighborhood. Costs of excavation: A completed wetland septic system should cost you between $1,200 and $4,500, but the cost will rise dramatically if you additionally install a pump or choose to go with the latter option. Traditional septic systems do not require electrical work, but any system that includes a pump or other mechanical apparatus will necessitate the installation of electrical wiring and equipment. Due to the fact that your local electrician will set the pricing and their effort is dependent on how much underground electrical line they have to run, it is difficult to estimate this cost.

The cost of your drain field or leach field, as well as the piping that connects your home to the tank, will be significantly higher if you’re building a septic system from the ground up from the beginning. A new drain field might cost up to $15,000, depending on its size.

How long does a septic tank last?

In general, septic tanks survive 20 to 30 years, although some can live up to 40 years or more. The material used to construct a septic tank, as well as how often it is cleaned, determine how long it will last. Steel septic tanks, which are less common, may rust out after 15 years, but many endure much longer. Concrete tanks have longer life spans, but they can be sensitive to acidic soils due to their construction. Plastic and fiberglass tanks are less vulnerable to the weather, although structural degradation is a greater worry with these types of containers.

Pumping and maintaining your tank on a regular basis will guarantee that it continues to function properly for many years to come.

Bottom line

When dealing with septic tank problems, there is a lot to consider. Even while it is vital to seek expert counsel, it is also beneficial to be prepared so that you can make informed judgments. In order to learn about your alternatives, whether you’re budgeting for a new tank or attempting to maintain existing system functioning, it’s a good idea to shop about, study reviews, and obtain different quotations. If you’re simply planning ahead or concerned about septic tank costs in the future, consider purchasing a home warranty to help offset the expenses.

The writers at ConsumerAffairs draw their inspiration for their work primarily from government data, industry experts, and original research published by other reputable publications.

  1. “Types of Septic Systems,” published by the United States Environmental Protection Agency (EPA). On September 26, 2021, the United States Environmental Protection Agency (EPA) published “How Your Septic System Works,” which was accessible online. United States Environmental Protection Agency (EPA), “How to Care for Your Septic System,” accessed on October 11, 2021
  2. “How to Care for Your Septic System.” On the 11th of October, 2021, it was accessible.

Did you find this article to be informative?|

Leave a Comment

Your email address will not be published. Required fields are marked *