How Close The Pipe Is To.The Top Of The Septic Tank? (Question)

A septic tank should always be “filled” to its normal liquid level, or the bottom of the outlet pipe which carries effluent to the absorption area. This normal liquid level is usually between 8” to 12” from the top of the tank on average (see picture at right).

projectperfecthome.com

• A typical septic tank has a 4-inch inlet located at the top. The pipe that connects to it must maintain a 1/4-inch-per-foot slope toward it from the house. This means that for every 10 feet of distance between the tank and the house, the inlet must be 2 1/2 inches below the point at which the pipe exits the house.

How deep is the top of a septic tank?

Dig Up The Lids In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid.

How deep is the septic tank outlet pipe?

After the solids settle out, effluent leaves the septic tank through the outlet pipe and flows to the drain field. The outlet pipe should be approximately 3 inches below the inlet pipe.

How deep is the pipe from the house to the septic tank?

A typical septic tank has a 4-inch inlet located at the top. The pipe that connects to it must maintain a 1/4-inch-per-foot slope toward it from the house. This means that for every 10 feet of distance between the tank and the house, the inlet must be 2 1/2 inches below the point at which the pipe exits the house.

Why the inlet pipe in the septic tank is higher than the outlet pipe?

Level the septic tank: The septic tank inlet tee is designed to be higher than the septic tank outlet tee. This helps assure that incoming sewage clears the baffle and enters the tank correctly, while outgoing effluent does not carry along floating solids, scum, or grease (which would clog the drainfield).

How far apart are septic tank lids?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

How do I find my septic tank lid?

You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath.

How many lids are on a septic tank?

In order to make repairs or perform regular maintenance or cleaning/pumping of the tank, access must be provided. There are usually two lids located at the top of the septic tank-one located over the inlet “T” and one located over the outlet “T” (see “Septic Components: Septic Tanks”).

How far should the distribution box be from the septic tank?

Common guidelines require at least 50′ clearance distance between a well and a septic system tank or 150′ between a well and a septic drainfield or leaching bed but you will see that different authorities may recommend different distances. Local soil and rock conditions can make these “rules of thumb” unreliable.

How much dirt should be on top of a septic tank?

Each layer should be uniform, no greater than 24 inches thick, and of nearly equal heights around the perimeter of the tank. However, compaction under the haunch (bottom curvature of some tanks) is best done in 6- to 12-inch layers.

What is the minimum depth of a sewer line?

How Deep Is a Sewer Line? Sewer lines on private property can be as shallow as 18–30 inches deep or as much as 5–6 feet deep. In areas with cold climates, the pipe will be buried deeper to prevent freezing in the winter.

How deep are drain fields buried?

A typical drainfield trench is 18 to 30 inches in depth, with a maximum soil cover over the disposal field of 36 inches.

How far down are water lines buried?

The general depth of underground water pipes is 12 inches below the frost line in your specific geographical area.

How far should inlet pipe go into septic tank?

The inlet baffle should extend at least 6 inches, but no more than 12 inches into the liquid level of the tank. The inlet baffle should extend 12 inches above the liquid level of the tank.

How much lower should the outlet be than the inlet on a septic tank?

Generally speaking, the outlet on a septic tank should be around 4–6″ lower than the inlet, depending on the size of the tank. The tank itself, when set in place, should be as level as possible. The height difference from inlet to outlet is accounted for in the tank’s manufacture.

Do all septic tanks have baffles?

Every septic tank contains two baffles, one at the inlet and one at the outlet.

Everything You Need to Know About Your Septic Tank

What is a septic tank, and how does it work? A septic tank is a water-tight container that is often constructed of concrete, fiberglass, or polyethylene to prevent flooding (plastic). In fact, it is only one component of the entire septic system, which includes several other components such as a distribution box, pumps, float switches, aerators, filters, and other accessories. Septic systems are used to treat wastewater on-site in many rural and suburban areas that do not have access to centralized sewage systems.

The components of a conventional septic tank are depicted in the diagram below.

These are:

1. The Tank: This is the water-tight tank into which wastewater from your house is sent once it has been collected. A hole, fracture, or any other structural damage should not be present. Access Ports: When a trained pumper comes to clean up your tank, they will utilize an access port. When it comes to tank cleaning, it is critical that the access port be large enough to allow the pumper to move the hose about within the tank properly. A common application for risers is to elevate septic tank access above ground level, eliminating the need to dig up your septic tank every time it has to be pumped. Last but not least, the access port should be securely secured with a child-resistant lid. It is vital for the protection of your family that septic tank lids are securely fastened with screws and that they are not cracked or damaged. Pipes for entering and exiting the septic tank: Wastewater from your house enters the septic tank through the intake pipe. After the particles have settled out, the effluent is discharged from the septic tank through the exit pipe and into the drainage field. There should be roughly 3 inches between the output pipe and the intake pipe. A baffle is fitted on the intake pipe within the tank, and it serves to keep the water out. It provides a variety of functions. Additionally, it helps to avoid the build-up of scum and its backup into the intake pipe It is also important for solids to settle in the tank that the input baffle be properly installed. When wastewater enters the septic tank, it should hit the entrance baffle, which will reduce the flow and prevent the tank from becoming agitated. This permits the contents of the septic tank to remain at rest, allowing the solids to sink to the bottom of the tank. The intake baffle can also prevent odorous odors from entering the sewage line and spreading throughout the home or business
2. And It is even more crucial than the inlet baffle to have an exit baffle in place because it helps to prevent scum and other particles from flowing directly into the outflow pipe and eventually into the drain field. Gas Deflector/Effluent Filter: As gas bubbles climb to the top of a septic tank, they may bring sediments with them. This is why an effluent filter is used. A gas deflector prevents these solid-carrying gases from entering the output line by preventing them from entering. However, while not every septic tank is equipped with an effluent filter, it is strongly suggested as an additional safety to prevent particulates from entering your drain field.

Any of the above-mentioned components in your septic tank should be checked for damage or missing parts as soon as possible, and the problem should be resolved by a septic system specialist. What is the operation of a septic tank? Each and every drop of wastewater from your home is channeled via a main drainage pipe and into your septic tank. Solids are prevented from entering your drain field by using the septic tank, which is just a settling tank that serves as a filter. Ideally, the water should be kept in the tank for at least one day in order to enable time for the solids to settle.

• Heavy materials, such as dirt and digested waste, will sink to the bottom of the tank and form a sludge layer at the bottom of the tank.
• Effluent is the term used to describe the liquid that exists between the sludge and scum layers.
• It is critical that solids are given adequate time and space to settle before being used.
• In fact, the Pennsylvania Department of Environmental Protection mandates a minimum capacity of 900 gallons for any new septic tank installations in the state (the table below shows recommended septic tank capacities for different sized homes).
• Ideally, you should have your septic tank emptied every two to three years, according to the Pennsylvania Septage Management Association (PSMA).
• If a drain field has been ruined by a buildup of sediments, it might cost tens of thousands of dollars to rebuild it.
• It is crucial to understand that your septic tank must be completely filled with liquid in order to function effectively.
• The septic tank diagram shown above depicts the correct operating level of a septic tank in a residential setting.
• The result is that whenever more wastewater is added to the tank, an equal volume of effluent will be discharged from the tank and drain into the drain field.
• The opposite is true if the liquid level is higher than the outflow line, which may signal a blockage in a line downstream from the septic tank or in the drain field.

If you’re wondering if your septic tank is full, a skilled pumper will consider it “full” once solids have filled one-third of the tank’s capacity. This is the time of year when your septic tank will need to be pumped.

How to Run a Septic Tank Line From Your House

A septic system is made up of two lengths of pipe that are connected together. Initially, it runs from the house, where the system services are located, to a tank, where the waste is separated and solids settle out. The second section runs from the tank to the drainage field, where fluids from the tank are dispersed into the earth underneath the tank. The process of installing the first run of pipe is quite similar to that of installing a traditional sewage line. It is necessary to maintain a downhill slope to the storage tank.

Locating the Septic Tank

The tank serves as the nerve center of the septic system. It is required to be situated between the residence and the drainage field. Each and every septic installation must begin with a soil test, and depending on the results, soil conditions may necessitate the placement of the tank in a less-than-ideal site for digging sewer lines. Also required are minimum setback distances from property borders, functioning wells, surface water and other obstructions to provide a safe working environment.

Tank Depth

A standard septic tank has a 4-inch intake at the top, which is positioned towards the bottom. Ideally, a 1/4-inch-per-foot slope toward the pipe from the house should be maintained by the pipe connecting to it. To put it another way, for every 10 feet of distance between a tank and a home, the inlet must be 2 1/2 inches lower than where the pipe departs the house at its lowest point. The pipe usually exits at ground level, although it may need to pass beneath a foundation footing or concrete pad in rare cases.

Digging the Trench

The trench for the septic pipe should be dug before the hole for the tank since you will need a backhoe to complete the work and the tank will get in your way if it is already in the ground. To allow rainfall to drain properly, the pipe should be placed on a 2- or 3-inch bed of drain rock, so remember to account for this extra depth when digging. It is normal to use a four-inch pipe, and it should be installed far enough down to link with the main soil stack, which is a three-inch pipe that runs vertically past the main bathroom and through the roof of the home.

Precautions

Local building and health agencies will demand permits for a septic tank installation. You will also be required to submit a design plan before the permits will be provided, so prepare ahead of time. This layout should be developed in collaboration with a local builder who is familiar with the unique characteristics of the topography in your neighborhood. Stay away from planting trees or plants near the tank, drainage field, or any of the pipe systems.

They will be drawn to the pipes in their hunt for nutrition, and their roots will be able to successfully block them. You will be unable to use your septic system until the roots have been removed from the pipe. Removal may be both expensive and time-consuming.

How Your Septic System Works

Underground wastewater treatment facilities, known as septic systems, are often employed in rural regions where there are no centralized sewage lines. They clean wastewater from residential plumbing, such as that produced by bathrooms, kitchen drains, and laundry, by combining natural processes with well-established technology. A conventional septic system is comprised of two components: a septic tank and a drainfield, often known as a soil absorption field. It is the septic tank’s job to decompose organic matter and to remove floatable stuff (such as oils and grease) and solids from wastewater.

Alternate treatment systems rely on pumps or gravity to assist septic tank effluent in trickling through a variety of media such as sand, organic matter (e.g., peat and sawdust), constructed wetlands, or other media to remove or neutralize pollutants such as pathogens that cause disease, nitrogen, phosphorus, and other contaminants.

Specifically, this is how a typical conventional septic system works:

1. All of the water that leaves your home drains down a single main drainage pipe and into a septic tank. An underground, water-tight container, often composed of concrete, fiberglass, or polyethylene, serves as a septic system’s holding tank. Its function is to retain wastewater for a long enough period of time to allow particles to sink to the bottom and form sludge, while oil and grease float to the surface and produce scum. Sludge and scum are prevented from exiting the tank and moving into the drainfield region by compartments and a T-shaped outlet. After that, the liquid wastewater (effluent) exits the tank and flows into the drainfield. The drainfield is a shallow, covered hole dug in unsaturated soil that serves as a drainage system. Porous surfaces are used to release pretreated wastewater because they allow the wastewater to pass through the soil and into the groundwater. In the process of percolating through the soil, wastewater is accepted, treated, and dispersed by the soil, finally discharging into groundwater. Finally, if the drainfield becomes overburdened with too much liquid, it can flood, causing sewage to flow to the ground surface or resulting in toilet backups and sink backups. Finally, wastewater percolates into the soil, where it is naturally removed of harmful coliform bacteria, viruses, and nutrients. Coliform bacteria are a kind of bacteria that may be found in the intestines of humans and other warm-blooded animals, with humans being the most common host. As a result of human fecal contamination, it is a sign of this.

The Guadalupe-Blanco River Authority has built an animated, interactive model of how a residential septic system works, which you can view here.

Do you have a septic system?

It’s possible that you’re already aware that you have a septic system. If you are not sure, here are some tell-tale symptoms that you most likely are:

• You make use of well water. In your home, the water pipe that brings water into the house does not have a meter. In the case of a water bill or a property tax bill, you will see “$0.00 Sewer Amount Charged.” It is possible that your neighbors have a septic system

How to find your septic system

You can locate your septic system once you have confirmed that you have one by following these steps:

• Taking a look at the “as constructed” drawing of your house
• Making a visual inspection of your yard for lids and manhole covers
• Getting in touch with a septic system service provider for assistance in locating it

Failure symptoms: Mind the signs!

A bad odor is not necessarily the first indicator of a septic system that is failing to work properly. Any of the following signs should prompt you to seek expert assistance:

• Water backing up into the drains of homes and businesses
• It is especially noticeable in dry weather that the drainfield grass is bright green and spongy. The presence of standing water or muddy soil near your septic system or in your basement
• A strong stench emanating from the area surrounding the septic tank and drainfield

How Does a Septic Tank Work?

Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.

How does a septic tank work?

Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.

It’s critical to understand how a septic tank works in order to maintain one.

Let’s take a look below ground and observe what happens in a properly operating septic system, shall we? After that, I’ll explain why things go wrong and offer you some tips on how to keep your system in peak operating condition.

Understand that a septic system is a cafeteria for bacteria

Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.

1. A layer of sludge settles to the bottom of the container.
2. 4.
3. Scum is mostly constituted of fats, greases, and oils, among other substances.
4. Grease and oils float to the surface of the water.
5. (5) A filter stops the majority of particles from reaching the exit pipe.
6. The effluent is discharged into the drain field.
7. Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.
8. The garbage is completely decomposed by aerobic bacteria found in gravel and dirt.
9. Potable water seeps into the groundwater and aquifer system from the surface.

Septic Tank Clean Out: Don’t abuse the system

Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank. However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.

• Drains are used to dispose of waste that decomposes slowly (or not at all). Cigarette butts, diapers, and coffee grounds are all known to cause issues. Garbage disposers, if utilized excessively, can introduce an excessive amount of solid waste into the system. Lint from synthetic fibers is emitted from washing machine lint traps. This substance is not degraded by bacteria in the tank and drain septic field. Bacteria are killed by chemicals found in the home, such as disinfecting cleansers and antibacterial soaps. The majority of systems are capable of withstanding limited usage of these goods, but the less you use them, the better. When a large amount of wastewater is produced in a short period of time, the tank is flushed away too quickly. When there is too much sludge, bacteria’s capacity to break down waste is reduced. Sludge can also overflow into the drain field if there is too much of it. Sludge or scum obstructs the flow of water via a pipe. It is possible for tree and shrub roots to obstruct and cause harm to a drain field. Compacted soil and gravel prevent wastewater from seeping into the ground and deprive germs of oxygen. Most of the time, this is caused by vehicles driving or parking on the drain field.

Get your tank pumped…

Your tank must be emptied on a regular basis by a professional. Pumping eliminates the accumulation of sludge and scum that has accumulated in the tank, which has caused the bacterial action to be slowed. If you have a large tank, it may be necessary to pump it once a year; but, depending on the size of your tank and the quantity of waste you send through the system, you may go two or three years between pumpings. Inquire with your inspector about an approximate guideline for how frequently your tank should be pumped.

…but don’t hire a pumper until you need it

Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.

Install an effluent filter in your septic system

Garbage from your home accumulates into three distinct strata.

The septic filter is responsible for preventing blockage of the drain field pipes.

Septic tank filter close-up

The septic tank filter is responsible for capturing suspended particles that may otherwise block the drain field pipes. Obtain an effluent filter for your tank from your contractor and place it on the outflow pipe of your tank. (It will most likely cost between $50 and $100, plus labor.) This device, which helps to prevent sediments from entering the drain field, will need to be cleaned out on a regular basis by a contractor to maintain its effectiveness.

Solution for a clogged septic system

If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.

1. Keep the effluent filter in place since it is required by your state’s health law.
2. Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
3. Your filter, on the other hand, should not require cleaning every six months.
4. A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
5. A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
6. Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.
7. More information on removing lint from your laundry may be found here.

Get an inspection

Following a comprehensive first check performed by an expert, regular inspections will cost less than $100 each inspection for the next year. Your professional will be able to inform you how often you should get your system inspected as well as how a septic tank functions. As straightforward as a septic system appears, determining its overall condition necessitates the services of a professional. There are a plethora of contractors who would gladly pump the sludge out of your tank, but many, in my experience, are unable to explain how a septic system works or how it should be maintained.

A certification scheme for septic contractors has been established in certain states; check with your state’s Secretary of State’s office to see whether yours is one of them.

Also, a qualified inspector will be able to tell you whether or not your tank is large enough to accommodate your household’s needs, as well as the maximum amount of water that can be passed through it in a single day.

You may be able to boost the performance of your system by using a product such as RID-X to introduce bacteria into the system. As you learn more about how a septic tank works, your professional should be able to tell you whether or not your system will benefit from this treatment.

Alternatives to a new drain field

If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.

• Pipes should be cleaned. A rotating pressure washer, used by a contractor, may be used to clean out the drain septic field pipes. The cost of “jetting” the pipes is generally around $200. Chemicals should be used to clean the system. A commercial solution (not a home-made one) that enhances the quantity of oxygen in the drain field should be discussed with your contractor before installing your new system. Septic-Scrub is a product that I suggest. A normal treatment will cost between $500 and $1,000. Make the soil more pliable. The practice of “terra-lifting,” which involves pumping high-pressure air into several spots surrounding the drain field, is authorized in some regions. Some contractors use it to shatter compacted dirt around the pipes. Depending on the circumstances, this might cost less than $1,000 or as much as $4,000 or more.

Protect your drain septic field from lint

When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.

Don’t overload the septic system

Reduce the amount of water you use. The volume of water that flows into your tank, particularly over a short period of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to save water.

Meet the Expert

Water consumption should be kept to a minimum. The volume of water that flows into your tank, particularly over an extended length of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to conserve water.

How Your Septic Tank Works

Understanding how your septic tank works will assist you in extending its life, saving money, and taking better care of your home’s plumbing system overall. As long as you are aware of the signs that anything is wrong with your tank, you will have time to have it repaired before it becomes a serious problem. It’s true that we find it simple to say all of this. We have a great deal of knowledge and expertise with septic tanks and their components. Finding out everything you can about your septic tank might be frightening.

Because we understand, we’ve created this primer to help you get started.

What is a septic tank?

A septic tank treats wastewater by the use of biological breakdown and drainage processes that occur naturally in the environment. Concrete, fiberglass, and polyethylene are the most common materials used to construct them. These big, rectangular or cylindrical tanks are used to collect all of the wastewater that is generated by your home’s sewer system. Septic tanks are connected to the sewer system by two pipelines, one at each end. A pipe connected to the tank’s input pipe allows waste water from your home’s sewage line to enter.

The output line then pumps the treated wastewater out of the tank and distributes it around the drain field. The waste contained within the tank is divided into three distinct layers: oil, liquid, and solid. ‌

What do septic tanks do?

All of the trash generated in your home is sent to the septic tank. A large amount of liquid waste is continuously absorbed and refilled in the tank. While this water is sitting in the tank, anaerobic bacteria are working to break down and separate the waste contained within it. The waste in the tank is separated into three kinds by the bacteria in the tank. Solid waste, often known as “sludge,” settles to the bottom of the tank after separation. Organic particles and waste products produced by bacterial digestion make up the majority of sludge.

The intermediate layer contains all of the water that remains after bacteria have completed their work of separating the sludge and scum.

It isolates and then redistributes remaining waste in an equal distribution over the drainfield surrounding it.

‌

How do I maintain my septic tank?

Regular pumping and protective maintenance are the two most important techniques to keep your septic tank in good working order. Pumping out your septic tank once every three to five years is a wise decision. If your tank is tiny or gets a lot of use, you may even want to pump it more frequently than once a week. A competent plumber will remove all of the sludge, scum, and residual water from the tank and dispose of it properly. When the tank has been thoroughly cleaned, new and healthy bacteria will begin to colonize the interior of the tank.

In order to preserve the safety of your septic tank, you need carefully manage the trees and plant life around it.

If you ever want assistance with your septic tank, contact the experienced plumbers at The Pink Plumber right away.

It is true that the more you know, the more you save!

FAQs — JT’s SEPTIC

Make sure to contact JT’s Septic as soon as possible! It is possible for us to assist you in diagnosing the problem and determining if it is a plumbing issue or a problem directly connected to your septic system. Wastewater backing up into more than one household fixture (even during dry weather), pooling water or muddy soil around your septic system or in your basement are all signs that your system needs to be checked. If you notice any of the following, contact us to have it checked: a strong odor around the septic tank and/or drainfield

Should I Use Septic Tank Additives?

According to current research, there is no clear proof that these items can prevent septic system failure or that they will improve system function. The addition of compounds to a septic tank will not eliminate the necessity for routine tank cleaning. Septic tank cleansers, rejuvenators, and primers that are promoted as such will not hurt your system, but they will not benefit it either. However, there is already a large amount of bacteria in the tank that will break down waste products, so using enzymes or yeast would not hurt your system at all.

Septic system additives should be avoided, according to the North Dakota State University Agriculture Communication. “Do Septic System Additives Work?” you might wonder. -Tank Refueling Station

what are the PVC pipes sticking up in my yard?

Septic tank cleanouts are often located between the home and the septic tank, and they are used to snake the input line from the house to the tank. If the PVC markers are labeled with “JT’s Septic,” they indicate that they are marking the access lids to your septic tank (buried directly under the labels). Alternatively, if the pipes are further away and appear to be arbitrarily arranged in relation to the house or tank, it is possible that they are inspection ports used to check the amount of liquid in the disposal area.

will household cleaning products harm my system?

The majority of specialists believe that the usual use of household cleaning solutions will not harm the system since it will not prevent the activity of bacteria in the tank from taking place as intended. A large amount of some chemicals, on the other hand, may interfere with the breakdown of wastes in the tank or cause the soil treatment area to get clogged. Please remember that the goods you use may ultimately make their way into the groundwater systems in your community.

How Often Should I Pump My Septic Tank?

Most tanks require pumping every 3-5 years, depending on the size of the tank, the amount of wastewater that flows into the tank on a daily basis, and whether or not the tank is equipped with a trash disposal. The state of Arizona currently does not have any laws requiring maintenance and inspection (with the exception of those pertaining to the sale of a home), but the Environmental Protection Agency and local health departments strongly recommend routine maintenance to help prevent groundwater contamination due to nitrogen, phosphorus, and disease-causing bacteria that can be found in wastewater.

I just had my tank pumped and it already looks full!?!

There is a distinction between being full and being overfull! An empty septic tank will fill up as quickly as you use up the quantity of gallons it can contain in terms of water use. The tank is designed to maintain a liquid level at or near the bottom of the outflow pipe at all times. (that exits into the disposal area). When you look down into your tank, it should appear to be completely filled. It is necessary to hire an expert to assess the quantity of scum and sludge in your tank in order to decide when it is time to pump it out.

Does anyone have to be home to have jt’s pump my septic tank?

We usually advise people to have someone at their house for our service, but it is not mandatory. Our service technicians are quick and fast when it comes to finding and pumping out a problem. We enjoy having a homeowner and/or a Realtor on site for our inspections so that they may discuss any concerns that we may discover. If we happen to miss you during our service, we are more than pleased to accept a credit card payment over the phone.

Does JT’s Septic do leach line work?

At this time, JT’s does not install or do any work on leach lines or disposal locations. We do minor repairs on septic tanks, as well as on the inlet and outlet sewer lines. Not sure if we can assist you? Just give us a call!

Why can’t you pump my septic tank out of the sewer cleanouts?

We have found that a tank cannot be efficiently pumped through sewage cleanouts because the pumps on our trucks are just too powerful, and there is no way to get all of the scum and debris out of the tank through a cleanout. It is advised that the tank access lids be used in order to remove all liquid and particles from the tank and to examine the baffles.

To empty the tank completely, we unlock all compartments and use a pump to remove the full contents of it. The fact that you do not pump via the primary access holes in the tank itself is a disservice to yourself and your system.

how do you know the size of my tank?

Our experts and inspectors can identify the size of the tank based on the form of the tank; tanks for a normal residence are generally 1,000 or 1,250 gallons in capacity, respectively (tanks may be smaller or larger depending on bedroom count, style of tank, etc). Our trucks are outfitted with clear sight glasses, allowing our specialists to keep track of the number of gallons they are extracting from your tank. Our specialists are also trained to measure the tank measurements on the job site in order to establish the approximate gallon capacity.

why do you recommend routine maintenance and frequent pump outs when I’ve not a had a problem in the last 10 years and I’ve never had my tank pumped?

Even while many homeowners are able to go several years over the suggested maintenance time without experiencing any problems, harm is gradually being done. Solids that are insoluble in water and cannot be broken down by natural microbes are stored in the tank. This builds up over time until the tank no longer has enough space to hold everything. As a result, the solids make their way to the drain field where they fill up the pores in the earth, causing poor drainage and, eventually, the failure of the septic system and drainfield.

How long will my septic system last?

All septic systems have a defined life span, which means they will ultimately cease to function. The length of time a system will survive is determined by the system’s size, installation, soil composition, the water table, neighboring trees and roots, the amount of usage and abuse, and, most crucially, the frequency with which it is maintained and pumped.

if I have a garbage disposal Can i use it?

Yes! It is OK to use the garbage disposal for a limited amount of time, such as for food crumbs that remain after doing the dishes. Pump outs will be more frequent if the disposal is used more frequently, which will result in higher costs. The usage of a trash disposal can have a negative impact on your septic system by increasing the quantity of suspended particles that enter the system. Soil treatment areas can get clogged with suspended particles, which reduces the soil’s ability to remove waste.

CAN I FLUSH WET WIPESFEMININE HYGIENE PRODUCTS?

No! The presence of this problem is one of the most prevalent we see in tanks. Wipes and/or feminine hygiene items block sewer pipes and do not decompose properly in the holding tank, causing backups.

how often can i do laundry?

It is critical not to overburden your computer system. Instead of completing a large number of loads in a single day, try to spread them out over the course of a week. Doing no more than two loads of laundry every day – one in the morning and one in the evening – is advised.

Can I have a water softener system with a septic system?

It is unlikely that a water softener will cause damage to most septic systems, albeit they may necessitate the installation of a somewhat bigger tank disposal area.

Can We Drive Over Our Leach Field?

It is not suggested to drive on the leach field and/or inletoutlet sewer pipes or the septic tank. It is possible to restrict or slow down efficient evaporation by compacting the soil over the leach lines.

Evaporation is a critical component of the drainage and disposal process. It is possible to induce settling and even rupture of sewage pipes by driving over them. It is possible to produce cracks in a tank by driving over it, especially if it is made of fiberglass or plastic.

do i have a septic systeM?

Do you utilize well water in your home? Is there no meter on the water main that leads into your home? Do your water bill or property tax bill display a “$0.00 Sewer Amount Charged” or “$0.00 Sewer Amount Charged”? What about your next-door neighbors? Do they have a septic system? Your home may have a septic system if any of the following questions were answered affirmatively:

How do I find my septic system?

Once you’ve confirmed that you have a septic system, you may identify it by looking at your home’s “as built” drawing, inspecting your yard for lids and manhole covers, or calling us for assistance.

How Far Does The Tank Have To Be Away From The House?

The normal setback distance from the home is 10 feet. Yavapai County is committed to upholding this obligation. Keep these setbacks as they are to allow for easier access and to avoid any potential foundation and moisture concerns.

An alarm is going off in my tank- what do I do?!

The sirens on certain alternative systems alert the homeowner to a possible problem prior to effluent or waste backing up into the house. The alarm may sound to warn a problem with the electrical system or a high quantity of liquid in the tank. A pump or float may be malfunctioning, in which case it is recommended to contact either JT’s or your alternate system maintenance provider for assistance as soon as possible.

Can I Plant A Tree Over My Leach Field?

No. Root invasion from trees is one of the most prevalent problems that affect septic systems today. Certain species of trees are extremely harmful to your septic system and should be avoided at all costs. Please check your local nursery for further information.

does jt’s provide portable storage tanks?

We’re sorry, but we don’t provide portable storage tanks at the present moment.

can jt’s facilitate a pipeline repair?

Yes! We are capable of repairing and replacing sewer inlet and outlet pipes. Our main line sewer camera service may also be used to plan infrastructure maintenance, as well as to aid with any and all forms of repair work. Please contact us if you would like to book a service.

why do you suggest running a sewer camera down my line?

A difficult blockage may necessitate the services of more than one plumber. Pipe obstructions can be caused by a variety of factors, including tree roots, grease, aging pipes, and foreign items. Our power snakes and Ridgid sewer cameras are excellent tools for identifying problems such as the following: Pipes that are broken, cracked, corroded, or collapsed are considered damaged and must be repaired or replaced. A clog is caused by a deposit of grease or a foreign item that prevents the passage of water.

Joints that are leaking—the seals between pipes have failed, enabling liquid to leak through.

COMMON PROBLEMS — JT’s SEPTIC

You should examine the sewer cleanout on the exterior of the home if you are hearing gurgling and all of the house fixtures are clogged. This is often a black 3-4 in color “inch ABS pipe with a threaded cap is available. Remove the cap (WARNING: BE CAREFUL! (WARNING: IT MAY CONTAIN SOME PRESSURE!) : Assuming the sewage line is completely dry, you will have a clog inside the home plumbing, directly in front of the cleanout valve. Make a phone call to a plumber and have them rooter the line. Sewer line cameras are available from several rooter/plumbing businesses.

You have two options at this point: call your preferred septic provider or pull up the tank lids yourself and check the water level and solids content in the tank yourself.

Most tanks erected after January 2001 include a filter that has to be cleaned at least once a year (we clean filters—please call us).

We’ll even notify you once a year when it’s time to clean your filters!).

You should contact your favorite plumber if only one or two fixtures are clogged (for example, one toilet or a specific sink or shower). It’s likely that you have a blockage in your sewage system. In the event that your septic tank is backing up, we can assist you!

GURGLES

Whenever you flush the toilet, the water gurgles, the toilet takes an unusually long time to flush, or the water in the shower turns brownish after you have done the laundry, you are receiving a subtle indication that trouble is brewing. In order to determine when the tank was last pumped, look through your records and then contact your preferred septic provider for assistance.

ODORS

If you are experiencing unpleasant odors within your home, such as rotten eggs, it is likely that a trap or vent inside your home is not venting correctly. Call your plumber right away since these gases are harmful to both people and animals!

ODORS OUTSIDE IN THE YARD

At times, the smells emanating from the roof vents will seep into the yard due to meteorological conditions. Make use of a plumber to elevate the roof vents and/or to place a charcoal filter in the vents, as needed. It’s important to remember that your septic tank is vented via the roof.

SURFACING IN THE YARD

If you notice effluent appearing in your yard, contact your septic service provider immediately. If you see this, it indicates that your leach line has failed and you should get help right away.

HEAVY SOLIDS- OVERDUE FOR PUMPING

Contrary to common perception, you DO need to have your septic tank pumped on a regular basis. Pumping maintenance should be performed on a regular basis, otherwise your system will get overwhelmed with solid waste and eventually cause damage to your leach lines. DON’T MAKE THIS HAPPEN TO YOU! This is an extreme example of a tank that is overflowing. There is sewage flowing from the tank access holes and into the yard!

grease build up in sewer pipes

Fats and grease should never be flushed down the toilet or sink. They have the potential to harden the lines and cause failure; they have the potential to generate an excessive buildup of the floating scum layer in the septic tank; and they have the potential to go into the disposal regions and adjacent soils and completely block the system off. A shattered lid can pose a serious threat to both animals and children. It is conceivable that they will fall through the cracked or broken lids and will not be noticed until it is too late to save themselves.

crushed or settled pipe

This is the second most prevalent problem we notice in septic systems that are less than 10 years old. In addition to blocking flow, loose fill soil surrounding the tank is causing a backup into the house since it is pulling the pipe with it as it settles. We have even observed instances when contractors installing new systems do not correctly pack the fill earth below the pipe, resulting in pipe settlement on systems that have not been utilized or have only been used for a short length of time (see below for an example).

SEWER OUTLET PROGRESSION

When it comes to modern septic systems, this is the most typical issue we encounter. Take note of the fact that the unsupported outlet pipe is being driven down by settling dirt.

Watch as the water level in the tank rises, forcing the flow of water in the inflow sewage line to slow. This will eventually result in a clog in the inflow sewer line at some point. The solids flowing down from the house will not be able to enter the tank correctly because of the high water level.

examples of settled sewer pipes:

INSTALLATION OF A TANK AND/OR REPAIR OF SEWER PIPESTHE “POLY” PIPEIMAGES BELOW PROVIDE AN EXAMPLE OF WHAT PIPENOTTO USES WHEN INSTALLING A TANK AND/OR REPAIR OF SEWER PIPES However, despite the fact that this grade of sewer pipe is less expensive at the time of purchase, it might end up costing you a lot of money in the long run!

settled inlet sewer pipe on unused system:

Even if the septic system has not been utilized in some time, it is conceivable that problems will be discovered during the inspection process. Pipes might settle on unoccupied ground and in yards as a result of faulty installation and/or automobiles and/or ATVs running over the pipes without realizing they are there. It may be beneficial to all parties to have a skilled inspector take a look at the system and diagnose any concerns, even though the County does not require an examination on an underused system before transferring ownership.

Roots growing in and around the septic tank:

In addition to disrupting the system by clogging or destroying drainage and distribution lines, tree roots can also enter the tank, causing it to leak. Foul odors, poor drainage, and patches of vegetation in the leach field are just a few of the signs that you may have a root problem.

ERODED BAFFLES

Solids are kept in the septic tank and away from the disposal area with the use of concrete baffles. Using baffles to reduce agitation of wastewater entering the septic tank and prevent particles from escaping the tank and entering the drainfield, baffles can assist avoid drainfield damage and extend the life of the drainfield. If the baffles are broken, missing, or have never been placed, the drainfield’s life expectancy will be reduced significantly. Baffle repair normally entails the placement of a plastic tee at the end of the sewer pipes to prevent them from clogging.

orangeburg sewer pipes

Orangeburg pipe was made in Orangeburg, New York, from 1860 to 1970, and was utilized to plumb numerous septic and wastewater systems throughout Yavapai County during that time period. Orangeburg pipe is produced from rolled tar paper (wood pulp that has been sealed with hot pitch) and was considered a low-cost alternative to metal, particularly after World War II, because of its flexibility and durability. In fact, the pipe itself is so soft that professionals might cut it with a knife during the installation process!

Orangeburg, on the other hand, is known for degrading over time (it has a 50-year lifespan at the most) and deforming when subjected to pressure.

If the septic system is approved, Orangeburg will normally be stated on the permits as the material for the inlet and/or outflow pipe material, respectively.

5 Signs Your Septic Drainfield Has Stopped Working

Unlike municipal septic systems, which consist just of a subterranean tank that collects waste and water, residential septic systems are more complex. Water finally departs the tank through an outlet pipe and into a network of long perforated pipes known as the leech or drainfield after reaching the tank’s interior. The drainfield is equally as vital as, if not more so than, the septic tank in terms of wastewater treatment. In the event that this component of the system begins to fail, prompt action might mean the difference between relatively small repairs and a total drainfield replacement.

1. Drainage is being slowed.
2. As long as there is still any water in the pipes of the field, the drains in your home will continue to function, albeit at a slower rate.
3. The presence of obstructions in the inlet or outlet pipe, as well as several other septic problems that are less difficult to resolve than drainfield problems, might result in delayed drainage.
4. 2.
5. You may detect puddles or spongy and mushy ground all over the place if you look closely.
6. A backup occurs when the water level rises to a level that forces sewage up the input pipe and into the lowest drains in your house, which is known as a back up in the system.
7. 3.

Drainfield leaks can provide visible consequences on the surface if the drainfield leaks at a higher rate than typical or contains decaying material that is meant to remain in the tank.

Returning Flow is the fourth step.

If you presume that the tank just need pumping, the service technician may discover water and sewage entering the tank from the outlet in a reverse flow, which would indicate that the tank requires more than pumping.

The presence of reverse flow from the drainfield is an obvious indication that you want jetting or pipe replacement services.

The Development of Odors In the end, you can utilize your sense of smell to detect indicators of drainfield issue.

Any sewage or toilet scents, even if they are weak and difficult to detect, signal that you should have a professional evaluate your home immediately.

This is the most effective way.

Whenever we observe a decrease in drainage capacity, we will inform you of the problem and your choices for resolving it before the system stops processing waste altogether.

In addition, we’re pleased to address any of your questions or concerns concerning your drainfield or septic system in general with a professional response.

Can A Septic Tank Cause Indoor Plumbing Problems?

Those who live in a home that is not linked to the municipal sewage system instead utilize a septic system to dispose of their waste. When homeowners understand how their septic system works, they are more likely to detect minor difficulties that may develop into major problems over time, prompting the need for emergency septic services. Residents in Gainesville should be aware that early signs of a septic system experiencing issues are frequently visible inside the home, according to Jones PlumbingSeptic Tank Service professionals.

How Does A Septic System Work?

An underground main sewer line connects drain pipes in your home to the septic tank in a domestic septic system, which is located beneath your property line. Solid waste settles in the bottom of the tank and grease accumulates at the top, resulting in a separation of wastewater according to matter. A drainage field is formed by the seepage of sewage water, which is then broken down by microorganisms. Over time, the sludge at the bottom of the tank builds and becomes a hazard. Regular septic tank servicing is required to avoid a full or overflowing tank, which can cause difficulties with the interior plumbing system if left unattended.

How Do Septic Tanks Affect Indoor Plumbing?

Whenever there are issues with a septic tank, the earliest signs of trouble generally arise in the plumbing system of the home or building. Some early indicators of septic tank difficulties include extended flushing of the toilets and poor draining in sinks and bathtubs, among other things. Water backing up into sinks, showers, and tubs is a common symptom of a clogged septic tank. Some homeowners may hear gurgling in their drainpipes or percolating sounds coming from their bathrooms as a result of this.

• The likelihood of a blockage in the indoor plumbing increasing if water is only backing up into one sink or toilet is greater than the opposite.
• Pouring boiling water down the drain or using a drain snake can assist clear less major obstructions.
• The system itself should be inspected by homeowners who feel their indoor plumbing problems are an indication of a failing septic system.
• Septic tank problems such as excessively lush plant growth or swampy conditions are indicative of a blocked or overflowing tank that is enabling waste to reach the drainfield.

Common Septic Tank Problems

Having a blockage in the inlet, outlet, or filter of your septic tank is the most typical septic tank problem that leads to indoor plumbing issues. As a result, you may require a septic tank pumping or filter replacement or cleaning, among other services.

Slow drainage and gurgling noises may indicate a clogged sewage vent, which may be repaired. If pipes get blocked or damaged as a result of tree roots or heavy machinery, more comprehensive septic tank repairs will be required in the future.

Septic System Maintenance

Regular septic system maintenance is essential in order to avoid costly issues down the road. A septic tank should be drained every two to three years, according to septic tank professionals in Gainesville, Florida. When dealing with bigger families, more frequent pumping may be required. In order to eliminate trash that has built up in the tank over time and to avoid obstructions, homeowners should have their Septic Tanks pumped on a regular basis. It is also a fantastic approach to uncover possible concerns before they become a problem.

Annual septic tank inspections are the most effective method of ensuring that a septic system is operating correctly.