What is the average size of a septic tank?
- An average-sized septic tank has a capacity of anywhere from 1,000 to 1,500 gallons (3,785 to 5,678 liters), though for high-impact areas large tanks with 5,000 to 10,000 gallon (18,927 to 37,854 liters) capacities exist.
How big is a 500 gallon concrete septic tank?
500 Gallon Chlorine Contact Tank Overall Length: 79” Overall Width: 48” Height to center line of inlet: 48 ” Height to center line of outlet: 45”
Is a 500 gallon septic tank big enough?
The minimum tank size for a three bedroom house is 1200 gallons. 500 or 750 gallon tanks used to be quite common in old houses, but they are not large enough for modern households, and are from a time without automatic washers, large spa tub, dishwashers, or multiple daily showers.
How big of a septic tank do I need?
The larger your home, the larger the septic tank you’re going to need. For instance, a house smaller than 1,500 square feet usually requires a 750 to 1,000-gallon tank. On the other hand, a bigger home of approximately 2,500 square feet will need a bigger tank, more than the 1,000-gallon range.
How do I find out how big my septic tank is?
One way to find out the size of your septic tank is through records kept from when the tank was installed. These records could be with the previous owner of your home. Another way to identify the tank size is to talk with the last company that serviced/pumped your tank.
What size septic tank do I need for a tiny house?
Tiny homes typically require a 500 to 1,000-gallon septic tank. Though, it’s not always possible to implement a tank of this size. In some states, for example, the minimum tank size is 1,000 gallons. There may be exceptions to this rule if your home is on wheels.
How often should a septic tank be pumped?
Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.
How much does it cost to pump a septic tank?
How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.
Is a 500 gallon septic tank big enough for two people?
A rule of thumb is the tank should be at least 400 gallons bigger than the amount of water it’ll handle. For example, if your water usage per day is 500 gallons then the septic tank should be 900 gallons. The average water usage of a person per day is 80-100 gallons, that’ll take us to our next factor.
How deep should a septic tank be?
Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.
How big of a drain field do I need?
The size of the drainfield is based on the number of bedrooms and soil characteristics, and is given as square feet. For example, the minimum required for a three bedroom house with a mid range percolation rate of 25 minutes per inch is 750 square feet.
How much does a 500 gallon plastic septic tank weigh?
Plastic septic tanks tend to weigh between 80 to 500 lbs, fiberglass tanks weigh between 300 to 500 lbs, while precast concrete septic tanks can weigh well above 8,000 lbs.
Manage calculator, unit converter & color codes
When you type math equations or conversions into the Google Search box, you will receive immediate results.
Calculator
It is possible to utilize the calculator to answer any type of math difficulty you may encounter, such as calculating the tip for a restaurant bill, creating graphs, or resolving geometry problems.
- Google.com or any other search engine will accept your equation as input. Calculator may be found by searching for:Calculator.
Calculations that you can do
- Mathematical operations, functions, and the value of physical constants. Base and representational conversions.
What is the best way to graph equations? By typing your functions into the search box, you can graph difficult equations in a short amount of time. You can see what an example equation looks like by visiting this page.
Tips
- Separate the formulae with a comma when plotting numerous functions at the same time. Zoom in and out, as well as pan across the plane, to have a better understanding of the function.
Functions you can graph
- The following types of graphs are available: trigonometric, exponential, and logarithmic
- 3D graphs (for desktop browsers that support WebGL)
Error notifications should be investigated and resolved.
“This function may not be plotted correctly”
One of the following was identified by the plotting algorithm:
- There are too many asymptotes. There are too many transitions between defined and undefined sections in the code. Due to extreme volatility, there are an excessive number of points on the graph that may not accurately represent the current function value.
Try moving the pan or zoom feature to a different part of the screen.
“Cannot zoom further”
Because to numerical constraints, the pan or zoom motion cannot be performed. Try moving the pan or zoom feature to a different part of the screen.
“Cannot pan in this direction”
Because to numerical constraints, the pan or zoom motion cannot be performed. Try moving the pan or zoom feature to a different part of the screen. Calculator for geometrical calculations When you use Google Search, you may locate geometry formulae and the answers to complicated geometry questions.
Open the geometry calculator
- Look up a formula on Google, such as: circumference of a circle
- Fill in the blanks with the values you are familiar with in the “Enter value” box. The Downarrow button is located next to “Solve for,” and it may be used to compute a different value.
Shapesformulas you can use
- Supported forms include: 2 and 3 dimensional curved shapes, platonic solids, polygons, prisms, pyramids, quadrilaterals, and triangles
- Supported shapes include: Area, circumference, rule of sines and cosines, hypotenuse, perimeter, Pythagorean theorem, surface area, and volume are all examples of formulae and equations that are supported.
Examples
- What is the volume of a cylinder with a radius of 4cm and a height of 8cm
- What is the formula for the perimeter of a triangle
- How to find the circumference of an oblong whose volume is 524 gallons
- Calculator a=4 calc b=7 calculator c=
- A2 + b2 = c2
The calculator does not appear to be working. If the calculator does not appear when you enter an equation, try the following:
- In order to ensure that your equation is something that can be calculated, Because dividing by zero does not provide a value, for example, if you search for “7*9/0,” you won’t see the calculator appear because dividing by zero does not produce a result. To see if it appears in your search results after that, try adding= to the beginning or end of your search
Unit converter
If you need to convert one measurement to another, you may do it with the unit converter. It is possible to convert from Celsius to Fahrenheit or from cups to liters, for example.
- Type your conversion into the search box, or search for: unit converter in the search results.
Conversions that you can do
- Temperature, length, mass, speed, volume, area, fuel consumption, time, and digital storage are all variables to consider.
Units that can be converted include:
Type of measurement | Available units |
---|---|
Angles | arc minutes, arc seconds, degrees, radians, revolutions, turns |
Area | acres, ares, barns, cricket pitches, dunams, football fields, football pitches, hectares, pings, Planck areas, sections, sqcm, sqkm, sqm, sqmm, square centimeter, square feet, square inch, square kilometer, square meter, square millimeter, square yards, stokes, survey townships |
Currency | Algerian dinars, Argentine pesos, Australian cents, Australian dollars, Bahrain dinars, Bolivian bolivianos, Botswana pula, Brazil reais, British pounds, Brunei dollars, Bulgarian levs, Canadian cents, Canadian dollars, Cayman Islands dollars, Chilean pesos, Chinese yuan, Colombian pesos, Costa Rican colones, Croatian kuna, Czech koruna, Danish kroner, Dominican pesos, Egyptian pounds, Estonian kroons, Eurocents, Euros, Fiji dollars, Honduran lempiras, Hong Kong dollars, Hungarian forints, Indian rupees, Indonesian rupiahs, Israeli shekels, Jamaican dollars, Japanese yen, Jordanian dinars, Kazakh tenge, Kenyan shillings, Kuwaiti dinars, Latvian lats, Lebanese pounds, Lithuanian litas, Macedonian denari, Malaysian ringgits, Mauritian rupees, Mexican pesos, Moldovan leu, Moroccan dirhams, Namibian dollars, Nepalese rupees, Netherlands Antilles guilders, New Zealand dollars, Nicaraguan cordobas, Nigerian naira, Norwegian kroner, Omani rials, Pakistan rupees, Papua New Guinean kina, Paraguayan guaranies, Peruvian nuevos soles, Philippine pesos, Polish zloty, Qatar riyals, Romanian lei, Russian rubles, Salvadoran colones, Saudi riyals, Seychelles rupees, Sierra Leonean leones, Singapore dollars, Slovak koruna, South African rands, South Korean won, Sri Lankan rupees, Swedish kronor, Swiss francs, Taiwan dollars, Tanzanian shillings, Thai baht, Trinidad dollars, Tunisian dinar, Turkish liras, Ugandan shillings, Ukrainian grivnas, United Arab Emirates dirhams, Uruguayan pesos, U.S. cents, U.S. dollars, Uzbekistani sum, Venezuelan bolivares fuertes, Venezuelan bolivars, Vietnamese dong, Yemeni rials, Zambia kwacha |
Data transfer rates | bits per second (bps), bytes per second (Bps) |
Electric capacitance | farads |
Electric charge | ampere hour, coulombs, Faradays |
Electric conductance | mhos, siemens |
Electric current | amperes, biots |
Energy | barrels of oil equivalent, British thermal units, BTU, calories, electron volts, ergs, foot-pounds, grams of TNT, joules, kilocalories, kilograms of TNT, megatons of TNT, megawatt hour, mwhr, therm, tons of tnt, watt hours |
Flow rate | CFM, CFS, cubic foot per minute, cubic foot per second, liter per minute, liter per second, LPM, LPS |
Force | dynes, kilograms-force, newtons, pounds-force |
Frequency | GHz, gigahertz, hertz, Hz, KHz, kilohertz, megahertz, MHz |
Fuel consumption | kilometers per liter, liters per 100 kilometers, miles per gallon |
Inductance | henries |
Information size | bits, nybbles, bytes, metric prefixes: kilobytes (kB), megabytes (MB),binary prefixes: kibibytes (KiB), mebibytes (MiB) |
Length | ångström, Astronomical Units, ATA picas, ATA points, chains, Ciceros, cubits, Didot points, english ells, fathoms, feet and inches, flemish ells, football fields, football pitches, french ells, furlongs, Half Ironman Triathlon bikes, Half Ironman Triathlon runs, Half Ironman Triathlon swims, Half Ironman Triathlons, hands, imerial cables, IN picas, IN Points, inches, indoor track lengths, international cables, Ironman Triathlon bikes, Ironman Triathlon runs, Ironman Triathlon swims, Ironman Triathlons, itinerary stadion, kilometers, Kpc, length of a cricket pitch, light days, light hours, light minutes, light seconds, light years, marathons, meters, metres, metres, microns, miles, Mpc, nails, nautical leagues, nautical miles, Olympic Pools, Olympic stadion, Olympic Triathlon bikes, Olympic Triathlon runs, Olympic Triathlon swims, Olympic Triathlons, outdoor track lengths, Parsecs, Planck Lengths, PostScript picas, PostScript points, Rack units, rods, scottish ells, Short Course Pools, Short Course Pools, smoots, spans, Sprint Triathlon bikes, Sprint Triathlon runs, Sprint Triathlon swims, Sprint Triathlons, TeX picas, TeX points, thou, Truchet picas, Truchet points, US cables, yards |
Light intensity and luminous intensity | candelas, footcandles, lamberts, lumens, lux |
Magnetic flux and magnetic flux density | gauss, maxwells, teslas, webers |
Misc | dioptres, emus, katal, moles |
Power | British horsepower, donkeypower, HP, kilowatt, kw, Kw, metric horsepower, mw, watts |
Pressure | atmospheres, barries, bars, inches of mercury, inches of water, mb, millibars, millimeters of mercury, pascals, poises, pounds per square inch |
Radiation dosage | grays, sieverts, rads, rems |
Radioactivity | becquerels, curies, rutherfords |
Speed | kilometers per hour, KPH, meters per second, miles per hour, MPH, nautical miles per hour |
Temperature | C, Celsius, F, Fahrenheit, K, Kelvin, Rankine |
Time | centuries, days, decades, fortnights, halakim, hours, leap years, lunar cycles, lustrum, millennium, minutes, months, seconds, sidereal days, sidereal years, weeks, years |
Unitless (numeric) | baker’s dozens, dozens, googols, great gross, gross, percent, scores |
Voltage | volts |
Volume | acre-foot, barrels of oil, beer barrels, beer firkins, beer hogsheads, beer kilderkins, board foot, board foot, bushels, cc, ccf, ci, cords, cubic centimeter, cubic centimetre, cubic feet, cubic inch, cubic kilometer, cubic meter, cubic millimeter, cups, English tierces, fluid barrels, fluid drams, fluid ounce, fluid oz., full kegs, gal., gallons, gills, Gross Register Tonnes, half barrels, hogsheads, Imperial beer barrels, Imperial bushel, Imperial bushels, Imperial dessertspoons, Imperial fluid drams, Imperial fluid ounce, Imperial fluid ounces, Imperial gallons, Imperial gills, Imperial minims, Imperial pecks, Imperial pints, Imperial quarts, Imperial tablespoons, Imperial teaspoons, km3, liters, litres, m3, minims, mm3, pecks, pints, puncheons, qt, quarter barrels, quarts, register tonne, shots, sixth barrels, sticks of butter, tablespoons, tbsp, teaspoons, tierces, tsp, wine firkins, wine rundlets |
Weight | amu, atomic mass units, Blintzes, butter firkins, carats, drams, earth masses, English stones, Farshimmelt Blintzes, funt, Furshlugginer Blintzes, grains, grams, imperial tons, jupiter masses, k, kilograms, lunar masses, metric tonnes, micrograms, ounces, pennyweights, pood, pounds, short tons, slugs, soap firkins, solar masses, stones, troy drams, troy ounces |
The metric prefixes yocto, zepto, atto, femto, pico, nano, micro, milli centi, deci deca, hecto, kilo can be used with many of the aforementioned units, as can the prefixes tera, peta, exa, zetta, yotta, and yotta. Abbreviated units can also be used with the abbreviated prefixes y, z, a, f, p, n, m, c, d, da, h, k, M, G, T, P, E, Z, and Y. Abbreviated units can also be used with the abbreviated prefixes y, z, a, f, p, n, m, c, For example, “km” can stand in for “kilometer,” while “GB” can stand in for “gigabyte.” It is possible to establish a speed unit by combining any length unit with a time unit, for example, “light-years per day” and “light-years per second.”
Color Picker
Color Picker allows you to select a color or convert from one color code to another using a single click. You can, for example, convert Hex colors to RGB colors.
- On google.com, type in your color code into the search box to see results. Color Picker may be found by searching for:Color Picker
Conversions that you can do You may convert color codes from the following sources: Color codes can be converted to the following:
Color codes you can search
Color codes such as: can be used to search for specific colors.
- Rgb (255, 255, 255)
- Rgb 255, 255, 255
- F0f0f0
- Color f0f0f0
- Pantone 214 u
- Pms 200 c
- Rgb (255, 255, 255)
Color Picker isn’t appearing
If a color that you looked for does not appear, it is possible that the color code was not input correctly. Try to find an acceptable color code in one of the forms indicated in “Color codes you may search for.” If you don’t find one, try another one. Please keep in mind that some browsers may not support the Color Picker.
Send feedback
If you receive an inaccurate response or wish to request a different sort of calculation, you may send feedback by clicking on the Send feedback button at the bottom of the page.
Was this information useful? What can we do to make it better?
500 Gal. Plastic Septic Tank for Sale
- The following items are available: 500 gallon septic tank (Snyder PartST21L)88″ L x 48″ W x 43″ H1 CompartmentFOB MS-$0.01
- 500 gallon septic pump tank (Ace Roto-Mold PartAST-0500-163″ L x 63″ W x 74″ H1 CompartmentFOB IASpecial Price)
- 500 gallon septic tank (Ace Roto-Mold Part Norwesco Part4078564, a 500-gallon septic pump tank, costs $932.99 “L x 64″ W x 67″ H1 CompartmentFOB California, Minnesota, New York, Ohio, Oklahoma, Utah, Washington Discounted Rate Norwesco Part4352297″ L x 48″ W x 42” H
- 500 Gallon Low Profile Septic Tank $962.99
- 500 Gallon Low Profile Septic Tank “H1 CompartmentFOB Mississippi, New York, Ohio, and Oklahoma From:$999.99 Up to: $1,648.94
- 500 Gallon Septic TankNorwesco Part41320101
- “51” L x 47″ W x 47″ H1 CompartmentFOB Georgia, Minnesota, Mississippi, Utah, WashingtonSpecial Price A 525 gallon septic pump tank that is approved by the state of Florida costs $1,047.99 and is 44″ long by 64″ wide by 67″ high “H1 CompartmentFOB FLSpecial Pricing H1 Compartment Norwesco Part44863130, a 500-gallon above-ground septic holding tank, is available for $1,133.99 “No CompartmentFOB MississippiSpecial PriceL x 52″ W x 22” H $1,149.99
- 500 Gallon Septic Pump TankSnyder Part5170000W9420360″ L x 60″ W x 63″ HSnyder Part5170000W9420360″ L x 60″ W x 63″ H “H1 CompartmentFOB Arkansas, California, Mississippi, and WisconsinSpecial Price a 500-gallon low-profile septic tank with plumbing already installed for $1,222.99 (Snyder Part4580297 “FOB Arkansas, California, Mississippi, Nebraska, and WashingtonSecondary Price$1,319.99
- Special Price$1,319.99
- NTO Part1000GB is a 1000 gallon above ground septic holding tank that is 136 inches long by 91 inches wide by 20 inches high “FOB MSSpecial Price$2,399.99
- HNo CompartmentFOB MS
500 Gallon Plastic Septic Tank – 1 Compartment (41320)
- Tanks from Georgia and Washington are available for shipment within 7 days
Important Note: Tank must be left 1/4 full at all times including installation.
Disclaimer: This tank is intended for usage below ground only.
State RequirementsApprovals
Our tanks must comply with a variety of health code standards that are in place across the United States. These codes are governed by the state or county in which you live, depending on your location. Please speak with your local health agency for assistance in choosing the tank you require.
Septic Tank Standards:
- Tank that has been rotationally molded into a single component that is seamless and waterproof
- Neither soil chemicals nor sewage gases have an effect on polyethylene. Tanks made of polyethylene will not rust or corrode. Strict quality standards guarantee that the septic tank is safe for the environment. Extensions for the risers are not included. Excellent shipping item that is virtually unbreakable.
Frequently Asked Septic Tank Questions
- If you ask the question, no, you cannot place the plastic septic tank beneath a driveway since it is not authorized, and doing so will invalidate the guarantee. Keep tanks out of the line of heavy and vehicle traffic regions, and don’t put them beneath driveways. If you’re looking for bedding or backfill, a sand/gravel mixture (sometimes known as “pea gravel”) is a good option. (Please refer to the installation instructions above.) 3. Is it possible to utilize a septic tank above ground? Underground plastic septic tanks are intended for use solely below ground. They are not intended for above ground usage. The use of above-ground storage tanks may result in the tank’s distortion and degradation. When compared to underground storage tanks, it is significantly more cost-effective to employ an above-ground storage tank that has been particularly constructed for above-ground uses. 4. Can hot water be held in plastic septic tanks? Yes, but only if the water temperature in the tank does not exceed 100 degrees Fahrenheit. The maximum storage temperature for polyethylene storage tanks is 120 degrees Fahrenheit. Containments with a temperature greater than 120 degrees Fahrenheit, even for a short period of time, might degrade the structural integrity of the tank and making it more prone to deformation and collapse
- 5. How do you gain access to underground plastic septic tanks? Each underground plastic septic tank is supplied with manhole access hatches, which allow you to gain access to the tank (1 or 2 depending on tank). Additionally, risers can be placed to the top of the tank to provide for access from the ground level. A riser would save you from having to dig up the dirt above the manway in order to get access
- Otherwise, 6. Is it possible to pick up a plastic septic tank in the area? In most circumstances, yes. You must place an order in advance in order to pick up a plastic septic tank and save money on shipping. When you are notified that your tank is ready for pickup, Plastic-mart will offer you with a six-digit trip number that will allow you to come in and pick up your tank Monday through Friday from 8:30 a.m. to 2:00 p.m. Plastic-mart and the local producers are grateful for the chance to provide local pick-up as well as the collaboration necessary to ensure that the process is as efficient as possible. The Georgia and Washington tanks are available for shipment within 7 days after order placement. Please contact us to inquire about the availability of other locations.
Plastic Septic Tanks – Single Compartment
Ace Septic TanksAce Roto-Mold septic tanks are stronger, easier to install, and less costly than old-fashioned concrete septic tanks- yet they still offer the quality construction and safety you expect. Manufactured from high-density polyethylene with U.V. inhibitors, Ace Roto-Mold tanks utilize a horizontal flow designed for below ground installations up to 36 inches. Ace Tanks are IAPMO approved and have passed strenuous stress tests. Each tank carries an individual serial code and is fully document from date of manufacture.Ace Roto-Mold septic tanks are designed and manufactured with rigorous quality controls. The trapezoidal deep-rib design and interior baffle system make Ace Tanks the industry choice. Only Ace tanks feature a custom-molded gasket in the lid. Manufactured from extruded Nitrile rubber, the gasket snaps into the lid and ensures a watertight seal. Our exclusive lid design locks in place with nylon ties, eliminating the need for metal fasteners that can corrode and fail.Ace’s unique tank baffle system slows the flow of wastewater and directs it to the middle of the tank so wastewater can separate from solids. An outlet baffles allows the partially treated liquids to flow out for further treatment. Advantages of Ace’s baffle design include added strength, versatility, and ease of installation.Septic tanks are available in one-compartment and two-compartment designs and are manufactured for containment of liquids up to 1.7 specific gravity.Ace Septic / Cistern Tank AccessoriesRemember to order your state specific internal plumbing kit. Links:Septic Tank Product Description, Function and ServiceSeptic Tank Installation ProceduresSpherical Septic Tank Installation ProceduresSeptic Tank Divider Installation Procedures
Norwesco Septic Tanks300 + 500 Gallon Spheres may be used as Septic Holding Tanks (Pump Out).SeeUnderground Water Tanksfor others available for Septic Holding Tanks.The world’s leading manufacturer of polyethylene tanks, NORWESCO has been producing polyethylene septic tanks since 1980. With that kind of experience, NORWESCO offers you proven products that you can count on for years of dependable, trouble-free service.For septic system replacement and new home construction, NORWESCO‘s polyethylene septic tanks are designed for durability and quick, easy installation. Any NORWESCO septic tank can be transported to the job site in a pickup truck and carried by just two people. That enables you to install the tank on your schedule.All NORWESCO septic tanks are manufactured by means of the rotational molding process, which produces a one-piece, seamless, watertight tank. Polyethylene is unaffected by soil chemicals and by the chemicals and gases present in sewage, so NORWESCO septic tanks will not rust or corrode and require no additional coatings as other tanks do. NORWESCO’s strict quality guidelines ensure an environmentally safe septic tank.NORWESCO septic tanks come equipped with manhole covers and detailed installation procedures. Manhole extensions and lid/riser combinations are available to bring tank access to grade and to meet code specifications. The 750, 1000, 1250 and 1500 gallon sizes are available in both one and two compartment configurations.NORWESCO septic tanks are for BELOW GROUND USE ONLY. Using the tanks above ground may result in deformation of the tank. It is far more cost-effective to utilize one of NORWESCO’s above ground tanks that are specifically designed for above ground use and applications.PRE-PLUMBING: All of our NORWESCO septic tanks that are 750 working gallons andabove are “pre-plumbed” with PVC inlet and outlet assemblies. Assemblies andtheir components are made of either SDR35 or SCH40 PVC depending on state orlocal code requirements. All assemblies are sized according to code requirementsas well. Finally, an EPDM gasket is placed between the “T” assembly and thetank wall to assure watertightness. NORWESCO septic tanks will arrive to youready for installation.WATERTIGHT DOMED LIDS: All septic tanks manufactured at all facilities, are equipped with a watertight domed lid. This domed lid is significantly stronger than previous lids we have offered. When leaving our factory, the lid(s) will be attached to the tank with stainless steel screws and come standard with a foamed, polyethylene gasket between the lid and the tank. This gasket provides a watertight seal at the lid area.MANHOLE EXTENSIONS AND LID/RISER COMBINATIONS: Again, at all facilities, the notches in the manhole area(s) of the tank have been removed as the “interruption” in the manhole, or circle, weakens that area. The lugs on the accessories have also been removed. See tank accessories for more information on the accessory items.NORWESCO septic tanks are backed by a full three-year warranty and have been certified by state and local health departments from coast to coast. Where applicable, NORWESCO septic tanks have been certified by both IAPMO and CSA.Across the United States and Canada, there are certain health code requirements that our tanks must meet. These codes are regulated by the state, county or province.Click here for Septic Tanks in HawaiiClick here for SepticWater Tank Accessories |
Septic Tanks
Listed below is a list of the septic tanks, chlorine contact tanks, and siphon dose tank packages thatCamden Supplyoffers, along with detailed descriptions of their features and specifications. Please call Camden Supply and chat with one of our staff if you require further information on a certain product.
Single Compartment Septic Tanks
A one-compartment steel-reinforced concrete septic tank, according to the script. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 56 inches
- Overall length is 79 inches
- Overall width is 48 inches
- Height to center line of inlet is 48 inches
- Height to center line of outflow is 45 inches
- Weight is 5,000 pounds.
600 Gallon Single Septic Tank
Specifications:
- Overall height is 62 inches
- Overall length is 79 inches
- Overall width is 48 inches
- Height to center line of inlet is 52 inches
- Height to center line of outlet is 49 inches
- Weight is 5,000 pounds.
1000 Gallon Single Septic Tank
Septic tank with a single compartment made of steel reinforced concrete (SRC). Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 96 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 8,000 pounds.
1250 Gallon Single Septic Tank
A one-compartment steel-reinforced concrete septic tank with the lower portion cast as a single piece so that there are no seams that come into touch with effluent. Specifications:
- Overall height is 60 inches
- Overall length is 117 inches
- Overall width is 68 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 10,400 pounds.
1500 Gallon Single Septic Tank
Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 11,700 pounds.
25003500Gallon Single Septic Holding Tanks
Single Septic Holding Tank with a capacity of 2500 gallonsSpecifications:
- Overall height is 68 inches
- Overall length is 144 inches
- Overall width is 78 inches
- Height to center line of intake is 61 inches
- Height to center line of outflow is 61 inches
- Weight is 16,000 pounds.
Single Septic Holding Tank with 35 00 Gallon CapacitySpecifications:
- Overall height is 98 inches
- Overall length is 144 inches
- Overall width is 78 inches
- Height to center line of intake is 91 inches
- Height to center line of exit is 91 inches
- Weight is 20,000 pounds.
Dual Compartment Septic Tanks
Description:Two-compartment tank with solids separator between the first and second compartments, holding 500 gallons and 500 gallons, respectively. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 96 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 10,000 pounds.
1250 Gallon Dual Septic Tank
Description:Two-compartment tank with a solids separator between the first and second compartments, holding 625 gallons and 625 gallons. Specifications:
- Overall height is 60 inches
- Overall length is 117 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 10,700 pounds.
1500 Gallon Dual Septic Tank
Description:Two compartment system with a capacity of 1000 gallons in the first compartment and 500 gallons in the second compartment. The dosage pump portion is usually found in the second compartment. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 11,700 pounds.
Triple Compartment Septic Tanks
Description:Three-compartment system with a solids separator between the first and second compartments. Each compartment holds 500 gallons. The dosage pump segment is usually found in the third compartment. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 12,000 pounds.
Chlorine Contact Tanks
Specifications:
- Overall height is 56 inches
- Overall length is 79 inches
- Overall width is 48 inches
- Height to center line of inlet is 48 inches
- Height to center line of outflow is 45 inches
- Weight is 5,000 pounds.
Siphon Dose Tank Packages
Specifications:
- It measures 56 inches in height, 79 inches in length, 48 inches in width, 48 inches in height from center line of intake, 48 inches in height from center line of outlet, and 5,000 pounds in weight. It is equipped with an indoor alarm and alarm float.
1000 Gallon Siphon Tank Package
Specifications:
- It measures 60 inches in height, 102 inches in length, and 67 inches in width. It measures 52 inches in height from the center line of the inlet and 52 inches in height from the center line of the outlet. It weighs 10,000 pounds. It comes with an indoor alarm and an alarm float.
1250 Gallon Siphon Tank Package
Specifications:
- It measures 60 inches in height, 117 inches in length, and 68 inches in width. It measures 52 inches in height from the center line of the inlet and 52 inches in height from the center line of the outlet. It weighs 10,400 pounds. It comes with an indoor alarm and an alarm float.
1500 Gallon Siphon Tank Package
Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of intake is 52 inches
- Height to center line of exit is 52 inches
- Weight is 13,000 pounds
- Includes indoor alarm and alarm float
What Size Septic Tank Do I Need?
Septic systems are used for on-site wastewater management, and they are located right outside your home. Perhaps your building project is located outside of a municipal service area, or you just like the notion of conducting wastewater treatment on a private basis. The optimum septic tank size is critical to the efficient operation of any septic system, regardless of the purpose for its installation. The percolation test, also known as a perc or perk test, as well as local codes, will be used to establish the position and quantity of field lines to install.
The size of the septic tank can be determined by the amount of water used or the size of the house. Do I require a large or small septic tank? Gary Carter/Corbis Documentary/Getty Images is credited with this image.
Why Septic Tank Size Matters
It is your septic tank’s job to collect and treat all of the water that exits your home through your toilets, showers, laundry, and kitchen sinks. For as long as 24 hours, the water may be kept in the tank, which also serves as a separation chamber where solids are removed from liquids in the process. When it comes to separating particles from liquids, the retention time is critical. The presence of bacteria in the tank aids in the breakdown of sediments. The size of the tank has an impact on how successfully the system can separate and break down the waste materials.
Although it might seem logical to believe that a larger tank is preferable, a tank that is too large for your water usage can interfere with the formation of germs.
Calculation by Water Usage
There are a variety of formulas that can be used to calculate the size of the septic tank that is required for your property. The most precise and dependable method is to measure water consumption. The size of the septic tank that is required is determined by the amount of water that will be handled and then dispersed into the field lines of the property. It should be noted that the minimum capacity tank permitted in many regions of the nation is 1,000 gallons. The following is a recommended tank size based on the total amount of water used by your household.
- 900 gallon tank for up to 500 gallons per day
- 1,200 gallon tank for up to 700 gallons per day
- 1,500 gallon tank for up to 900 gallons per day
- Tank holds up to 1,240 gallons per day
- Tank capacity is 1,900 gallon.
Calculations By House Size
The number of bedrooms in your home, as well as the square footage of your home, are less precise guides for determining the size of your tank. The maximum number of bedrooms that may be accommodated by a 1,000 gallon septic tank is two. It’s difficult to say due to the fact that water consumption varies depending on your situation. These estimates are based on the assumption that all bedrooms will be occupied, and the anticipated water consumption is based on this assumption. It is impossible to do these calculations if you live alone in a three-bedroom house.
The suggested tank sizes are listed below, according to the number of bedrooms in the house.
- Three bedrooms under 2,500 square feet: 1,000 gallon tank
- Four bedrooms under 3,500 square feet: 1,200 gallon tank
- And five or six bedrooms under 5,500 square feet: 1,500 gallon tank
- One or two bedrooms under 1,500 square feet: 750 gallon tank
- Three bedrooms under 2,500 square feet: 1,000 gallon tank
Estimated Cost
Similarly to the cost of any other commodities or services, the price might vary significantly based on where you reside and the current market circumstances. Let’s pretend you’re going to install a concrete septic tank for the sake of planning your project. These are by far the most prevalent, and they have a somewhat lengthy life span. The cost of a typical 1,000-gallon septic tank is between $500 and $700 dollars. The cost of upgrading to a 1,250-gallon tank will be at least $100 more. After three to five years, depending on the size of the tank, you could anticipate to have a cleaning job to do.
If you’re debating between two different tank sizes, knowing your financial constraints might assist you make your ultimate selection.
Although your contractor should be able to assist you in sizing your tank, understanding how to roughly determine your size requirements will help you anticipate how much you’ll need and how much you’ll spend on your tank.
500 Gal Plumbed Low Profile Septic Tank
Low profile seamless single compartment septic tank (Snyder 1000900W95301) with a capacity of 500 gallons per compartment. There is no requirement for installation, specific backfill, or water filling.
- It has a capacity of 500 gallons, measures 48 inches in diameter and 42 inches in height, and weighs 189 pounds. It is made of high density polyethylene (HDPE), is gray in color, and has a lid and a manhole with a specific gravity of 1.0 (for water only).
- Please keep in mind that all photos and drawings are for illustrative reasons only and may not always depict the actual product. Plastic tanks’ dimensions may vary by +/- 3 percent (typical rotational molding tolerance), depending on the material. Clients are responsible for determining whether or not the product material(s) are compatible with and suitable for their intended application(s). Tanks must be installed and used in accordance with the manufacturer’s instructions for usage and installation in order for the warranty to be valid. Plastic tanks are meant to withstand atmospheric pressure only, and venting systems should be sized to prevent pressure or vacuum from exceeding 12″ water column (0.018 psi). According to the tank manufacturer’s guidelines, flexible connectors must be used on all fitting connections.
What size of septic tank do I need?
Probably one of the last things on your mind when you are constructing a new house is the location of your septic system. After all, shopping for tanks isn’t nearly as entertaining as shopping for cabinetry, appliances, and floor coverings. Although you would never brag about it, your guests will be aware if you do not have the proper septic tank placed in your home or business.
septic tanks for new home construction
The exact size of the septic tank is determined mostly by the square footage of the house and the number of people who will be living in it. The majority of home septic tanks have capacities ranging from 750 to 1,250 gallons. A 1000 gallon tank will most likely be required for a typical 3-bedroom home that is smaller than 2500 square feet in size. Of course, all of this is dependent on the number of people who live in the house as well as the amount of water and waste that will be disposed of through the plumbing system.
For the most accurate assessment of your septic tank needs, you should speak with an experienced and trustworthy sewer business representative.
planning your drainfield
Here are some helpful hints for deciding where to locate your drainfield when you’re designing it.
- Vehicles should not be allowed on or around the drainfield. Planting trees or anything else with deep roots along the bed of the drain field is not recommended. The roots jam the pipes on a regular basis. Downspouts and sump pumps should not be discharged into the septic system. Do not tamper with or change natural drainage features without first researching and evaluating the consequences of your actions on the drainage field. Do not construct extensions on top of the drain field or cover it with concrete, asphalt, or other materials. Create easy access to your septic tank cover by placing it near the entrance. Easy maintenance and inspection are made possible as a result. To aid with evaporation and erosion prevention, plant grass in the area.
a home addition may mean a new septic tank
Do not make any big additions or renovations to your house or company until you have had the size of your septic system assessed. If you want to build a house addition that is more than 10% of your total floor space, increases the number of rooms, or necessitates the installation of new plumbing, you will almost certainly need to expand your septic tank.
- For a home addition that will result in increased use of your septic system, your local health department will require a letter from you that has been signed and authorized by a representative of your local health department confirming that your new septic system is capable of accommodating the increase in wastewater. It is not recommended that you replace your septic system without the assistance of a certified and competent contractor.
how to maintain your new septic system
Septic tank cleaning and septic tank pumping services are provided by Norway Septic Inc., a service-oriented company devoted to delivering outstanding septic tank cleaning and septic tank pumping services to households and business owners throughout the Michiana area. “We take great delight in finishing the task that others have left unfinished.” “They pump, we clean!” says our company’s motto. Septic systems are something we are familiar with from our 40 years of expertise, and we propose the following:
- Make use of the services of a qualified specialist to develop a maintenance strategy. Make an appointment for an annual examination of your septic system. Utilize the services of an effluent filter to limit the amount of particles that exit the tank, so extending the life of your septic system. Waste items should be disposed of properly, and energy-efficient appliances should be used. Make sure you get your septic system professionally cleaned every 2 to 3 years, or more frequently if necessary, by an experienced and qualified expert
- If you have any reason to believe that there is an issue with your system, contact a professional. It is far preferable to catch anything early than than pay the price later. Maintain a record of all septic system repairs, inspections, and other activities
common septic questions
Here are some of the most frequently asked questions by our septic customers.
How do I determine the size of my septic tank?
If you have a rectangular tank, multiply the inner height by the length to get the overall height of the tank. In order to find out how many gallons your septic tank contains, divide the number by.1337.1337
How many bedrooms does a 500-gallon septic tank support?
The exact size of the septic tank is determined mostly by the square footage of the house and the number of people who will be living in it.
The majority of home septic tanks have capacities ranging from 750 to 1,250 gallons. A 1000 gallon tank will most likely be required for a typical 3-bedroom home that is smaller than 2500 square feet in size.
How deep in the ground is a septic tank?
Your septic system is normally buried between four inches and four feet underground, depending on the climate.
500 Gallon Plastic Septic Pump Tank
However, they still provide the excellent structure and safety that you expect from an Ace Roto-Mold septic tank. They are stronger, less difficult to install, and less expensive than traditional concrete septic tanks. Ace Roto-Mold tanks, which are made of high-density polyethylene with ultraviolet inhibitors, have a horizontal flow that is suitable for below-ground installations up to 36 inches in depth. NSF has certified that the 1000, 1250, and 1500 gallon double-compartment septic tanks meet or exceed the requirements of the IAPMO Z1000 and CAN/CSA-B-66 standards.
- A thorough quality control process is used in the design and construction of Ace Roto-Mold septic tanks.
- Ace tanks are the only ones that have a custom-molded gasket in the lid.
- With our innovative lid design, nylon ties hold the lid in place, avoiding the need for metal fasteners that might corrode and fail in the long run.
- By using an exit baffle, you may enable the partially treated liquids to flow out and be treated further.
- Septic tanks are available in one-compartment and two-compartment configurations, and they are designed to hold liquids with specific gravities up to 1.7.
How Big of a Septic Tank Do I Need?
If you’re constructing a home, a septic tank is unquestionably one of the most significant considerations you should take into consideration. Septic tanks are used to dispose of wastewater outside the residence. The size of the septic tank is one of the most important elements to consider when determining whether or not it will function properly. In this article, we’ll go over why septic tank sizes are important and how to establish the appropriate tank size for your property based on your requirements.
Why Septic Tanks’ Sizes Matter?
To understand why size matters in this situation, we must first clarify what septic tanks are used for. Septic tanks are the initial stage of a septic system’s journey through the earth. They are the initial point of contact for all of the water in your home. The wastewater might originate from anywhere: the laundry, showers, toilets, or even the kitchen. Liquids are separated from solids in this facility. After the solids have been broken down, everything runs into the drainage system, which is the other component of the septic tank system.
- Retentions occur as a result of the bacteria present in the tank.
- Now, if the tank is insufficiently large.
- Because more wastewater is being pumped into the system, the waste is being driven out into the drainage system before the bacteria have finished breaking it down.
- However, if the tank is too large, there will not be enough heat to support the growth of bacteria.
A lack of microorganisms results in a lack of breakdown of waste materials. The same problems would arise as a result of this. Check out this page for helpful hints on how to take the best possible care of your septic system.
How to Decide What Size Is Best?
Before we get into the specifics of how much of a tank you require, we’d want to point out something very crucial.
How to Calculate a Tank’s Capacity in Gallons?
If the tank is rectangular in shape, the dimensions are as follows: Length x Width x Depth in feet x 7.5 = gallons If the tank is circular, the cubic capacity is equal to 3.14 x the radius squared x the depth (all in feet). Cubic capacity multiplied by 7.5 equals gallon capacity. There are various elements that influence the size of the septic tank that should be installed. They’re right here!
1. Water Usage
You may decide the size of the tank you require based on the amount of water used by your home. This is often considered to be the most efficient component to consider, because the size of the tank required is directly proportional to the amount of water it can hold in its capacity. In order to ensure compliance with local regulations, learn about the minimum tank size necessary in your area. The restrictions differ from place to location, but in most cases, a minimum capacity of 1000 gallons is permitted.
For example, if your daily water use is 500 gallons, your septic tank should have a capacity of 900 gallons.
2. Number of People Residing in the House
According to whether you live alone or with 6 or more family members, the size of the tank you require varies. To calculate, use the procedure outlined above. If there are four people living in the house, they can consume up to 400 gallons of water each day on average. According to the 400-gallon rule, you should get a tank that holds at least 800 gallons.
3. Size of the House
In this case, you may argue that the size of the home or the number of bedrooms it contains doesn’t important or that using such parameters would be misleading. Because there are so many circumstances in which there are vacant rooms, it’s possible that you’ll think this way. This would be the incorrect way of thinking about it, because septic tanks typically have a lifespan of 50-70 years, depending on the manufacturer. During those years, other families may be interested in purchasing or renting the house.
There are two methods to go about calculating the value.
Using the Number of Bedrooms in the House
Regulations such as this one determine the average use based on the assumption of two persons per bedroom. To be on the safe side, follow this formula: there are two persons in every bedroom, and each person requires 100 gallons of water. Then, add 400 gallons to the mix. This should provide you with a good idea of how large your tank should be in terms of volume. For example, if you have three bedrooms and six people, 600 + 400 equals a 1100 gallon tank.
Using Square Feet
You might double the square footage of your home by two, or you could just apply the usual estimating method, which goes as follows: If your home is smaller than 1,500 square feet, you’ll need a 750-gallon tank. If your home is smaller than 2,500 square feet, you will need a 1,000 gallon tank. If your home is smaller than 3,500 square feet, you will need a 1,250 gallon tank.
If your home is smaller than 4,500 square feet, you will need a 1,250 gallon tank. If your home is smaller than 5,500 square feet, you’ll need a 1,315 gallon tank. In any case, it provides you with an approximated average.
Wrapping Up
You now see how critical the size of the septic tank is to ensuring that the whole sewage system functions well and does not cause you any immediate or cumulative problems in the future. In this tutorial, we examined the most significant considerations to bear in mind, which include the amount of water used, the size of your home, the number of people who live there, and the number of bedrooms in the home. Make sure to do these calculations ahead of time to avoid any complications in the future.